Can Badlands 2500 Winch be Wired to 110 AC Power Source

Question

Question:

can I wire the winch into a 110 outlet ?

asked by: Scott E

0

Expert Reply:

We have winches with similar capacities to the Badlands 2500 you have that are designed to be used with 110 AC power like the Dutton Lainson StrongArm part # DL24872 but I can't recommend attempting to connect a DC winch to an AC power source unless you used an AC to DC converter like the 40 amp part # 329-GX2440.

expert reply by: Jameson C

0

Answer 1

You would not be able to mount a winch to a wood bed if you are going to put any kind of load on it. You would need to get the winch mounted to the steel frame somehow. To do this you can use U bolts to attach through the wood bed to the trailer…

view full answer...

Answer 2

The amperage on the 12 volt power circuit will depend on the amperage draw of the item receiving the power on the trailer. When aftermarket 7-way trailer connectors are installed on vehicles, it is recommended to have a 40-amp circuit breaker inline…

view full answer...

Answer 3

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 4

All of the available winches run off of a 12V power source or 120V power source and do not run off 110V. The best way to use a winch is to use a 12V battery but if you do not have a 12V power source then you can use a converter to convert the 110V to…

view full answer...

Answer 5

There are many factors that can go into selecting the correct electric which, if you want to learn more then be sure to check out the article below. That said, to simplify things we recommend using a 2:1 ratio which means the winch will need to be…

view full answer...

Answer 6

The stop light switch that you will need to connect the red wire to on the Brake Control Plug-In Harness for Tekonsha part #20127 may be pre ran to a set of wires taped to the underside of the drivers side vehicle dash. If the wires are not present…

view full answer...

Answer 7

The etrailer ATV Winch - Synthetic Rope - Hawse Fairlead - 5,000 lbs, part #e98989, is water resistant to IP66 specifications. I have included a video demo link below.

view full answer...

Answer 8

You could use the Bulldog Winch part #BDW15019 that you referenced on a boat trailer. Bulldog Winch has told us that this specific winch will fit on the standard mounts for boat trailer and also will work great for this application. I think a lot of…

view full answer...

Answer 9

I really wish there was a cheap and easy way to lock out a Titan model 60 actuator but the only way would be with an electric lock out like the part #T4748800. This threads onto the back of your current actuator and once ran to the reverse light…

view full answer...

Answer 10

Yes, the direct replacement for your Titan 225S passenger's side brake caliper is the #K71-773-02. For the driver's side use part #K71-773-01. These brake calipers are compatible with 3,500 lb axles with 10 inch brakes, which according to…

view full answer...

Answer 11

The Dutton-Lainson StrongArm 12-Volt DC Electric Winch with Remote #DL25220 is only compatible with a strap but we do have 12V winches with a remote that are compatible with a cable. For example, we have the Bulldog Winch #BDW15017 which has an…

view full answer...

Answer 12

The Brophy #BM20 ball mount will not reduce your vehicle's towing capacity like an adapter or extender will. The ball mount's max towing capacity is 10,000 pounds and its max tongue weight is 1,000 pounds. You should check the capacity of…

view full answer...

Can Badlands 2500 Winch be Wired to 110 AC Power Source

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching