How Many of the Trailer Hub and Drum Assembly AKHD-550-35-EZ-K Are Needed for a Single Axle Trailer

Question

Question:

Can you tell me if AKHD-550-35-EZ-K is a set of two for the axle or if I would need to order two of those for a single axle trailer please?

asked by: Mark H

0

Expert Reply:

If you have a single axle trailer you would need to order two Trailer Hub and Drum Assembly part # AKHD-550-35-EZ-K as they are sold individually.

expert reply by: Conner L

0

Answer 1

The Dexter 8-283 is an obsolete 2800lb 10 x 1-1/2 inch hub that used a LM67048 inner and a L44649 outer bearing. Unfortunately, we don't have any hubs that would be compatible with the spindles on your axle. Your best bet at this point would be…

view full answer...

Answer 2

The Redline Replacement Trailer Hub Wheel Stud Drive-In 1/2 Inch x 1-7/8 Inch #RG03-060 referenced in your question is available only in this set of 4. These are not currently available as a single item. We do have the slightly longer Trailer Hub…

view full answer...

Answer 3

Hello 89 5, We do have a 3,500 lb axle with 89 inch hub face to hub face and 74 inch spring center to spring center that will work with a hub that has a 5 on 5" bolt pattern, but the hub just needs to be purchased separately as they don't…

view full answer...

Answer 4

Hey Erik, so if the coupler on your 2007 MasterCraft boat trailer is labeled a UFP or a Dexter actuator and looks like the #DX99FR then yes this inner member is correct replacement to get it working again. There isn't a way to look up what your…

view full answer...

Answer 5

For a 3,500 lb hub/drum replacement that will work well to replace your AL-KO 8500 you'd want the hub part #84546UC3-EZ which fits the spindle and has the 5 on 4-1/2 inch bolt pattern you need. For brake assemblies then the Electric Brake…

view full answer...

Answer 6

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 7

I've attached an article to help you with how to measure to determine your bolt pattern. With 3 inches on center, you have a 5 on 5 inch bolt pattern. The 5 on 5 bolt pattern is generally only found on 3500 lb axles. For a hub and drum assembly,…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

Thanks for reaching out, Michael! The Dexter Electric Trailer Brakes #K23-086-087-00 are compatible with 3,500 lb axles and have the standard 4-bolt pattern so if that matches the specs of your axle then this will definitely work for your…

view full answer...

Answer 10

From what I found online, a 2020 Jeep Wrangler and Grand Cherokee use a 5 x 127mm bolt pattern, which is equivalent to a 5 on 5 bolt pattern like the #AKHD-550-35-EZ-K hub/drum you'd looked at. A 3500 lb axle will typically use a L8149 inner and…

view full answer...

How Many of the Trailer Hub and Drum Assembly AKHD-550-35-EZ-K Are Needed for a Single Axle Trailer

Product Page this Question was Asked From

Continue Researching