How To Find a Replacement Drop Leg for a Ram Trailer Jack

Question

Question:

Hi, will the Ram jack leg jf-1005h-z fit in the Ram Trailer Jack Model 2000 series? 3000lb. support capacity/2000lb. lift capacity Thank you for your time.

asked by: Sean S

0

Expert Reply:

The Drop Leg for Ram Jacks part # JF-1005H-Z works with any Ram Trailer Jack that has a 2" inner tube diameter. This is most likely what you have so yes it should work for you although I am not sure exactly which jack you have.

expert reply by: Conner L

0

Answer 1

You would choose a side wind or top wind jack based on several factors. Each has its advantages. If clearance is an issue for the radius of a top wind, then you would choose a side wind. The opposite is also true. It is my experience that a side…

view full answer...

Answer 2

Good question! The etrailer Drop Leg for etrailer and Ram Jacks - 13-1/4" Tall part #JF-1005H-Z is the perfect drop leg for your jack. The Lippert Components electric jack use a 2" inner tube diameter and that is specifically what this drop…

view full answer...

Answer 3

The smoke and white covers that are on the Ventline roof vents are both going to let quite a bit of light into the trailer. However, due to the translucent nature of the smoke covers they would let more light in. Both would last about the same amount…

view full answer...

Answer 4

The smoke might let a little more light through it, but nothing that noticeable. And aside from that either color does not have the reputation as lasting longer than the other. The white version is part #BV0554-01 and the smoke version is part…

view full answer...

Answer 5

Thanks for the information on your trailer. For your axle with brakes I recommend the Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb E-Z Lube Axles - 12" - 6 on 5-1/2 #AKHD-655-6-EZ-K if you have the spindles with the integrated grease…

view full answer...

Answer 6

Yes, all you'll need to do is disconnect the three wires running from the converter section in your Progressive Dynamics 4100 #PD4135K from the AC distribution panel (circuit breaker, ground bus bar, neutral bus bar). This will cut the power…

view full answer...

Answer 7

I do not recommend installing an a-frame jack in a manner that requires you to disassemble it. What I do suggest, since you have fabrication capabilities, is that you make a new a-frame jack mounting point on the trailer at the height you want it and…

view full answer...

Answer 8

Yes, the Drop Leg for etrailer and Ram Jacks - 13-1/4" Tall - 5-1/4" Diameter Footplate - Zinc, part #JF-1005H-Z, is compatible with Round A-Frame Trailer Jack - Topwind - 14-1/4" Lift - 2,000 lbs, part #TJA-2001-B. I have included a…

view full answer...

Answer 9

The correct brake controller harness for your 2023 Ford E-350 to install a Tekonsha Prodigy P3 part #90195 is the part #22292. The connector on your E-350 is in a really unusual location behind the vents above the stereo. To see how to access it…

view full answer...

Answer 10

The overall size of the Furrion Over the Range RV Convection Microwave part#FMCM15SS is 29-15/16" wide x 16-3/8" tall x 15" deep and requires a 30" cutout. If this matches the opening and size of the model you have this will be a…

view full answer...

Answer 11

We have a really great trailer jack replacement for what you have with the etrailer Sidewind Jack part #TJA-5000S-B. This is a sidewind jack like what you have but as you can see in the attached install video it can install with the handle on the…

view full answer...

How To Find a Replacement Drop Leg for a Ram Trailer Jack

Product Page this Question was Asked From

Continue Researching