Do The Hitch Ball Holes Line Up On a Curt EZr and B&W Turnoverball for a 2005 GMC Sierra

Question

Question:

I have a bed that originally had a BandW goooseneck hitch installed so the holes are in the bed already. Do you know if this hitch will fit the same holes as the BandW?

asked by: George

0

Expert Reply:

The Curt EZr Double Lock Underbed Gooseneck Trailer Hitch with Installation Kit part # C619-648 hitch ball opening will not line up with the B&W Turnoverball Gooseneck Trailer Hitch hitch ball opening on your 2005 GMC Sierra. The hitch ball opening for the Curt EZr will sit further away from the end of the bed when compared to the B&W Turnoverball. Therefore, the best option for you would be to re-install the B&W Turnoverball Underbed Gooseneck Trailer Hitch part # BWGNRK1059 for 1500 models, part # BWGNRK1067 for 2500 models, or part # BWGNRK1062 for 3500 models.

expert reply by: Conner L

0

Answer 1

From a function point of view there isn't a huge difference between the two Curt gooseneck hitches #C60712 and #C619-648. You might notice that the EZR has a smaller plate that has larger u-bolts for safety chains and the Double Lock has smaller…

view full answer...

Answer 2

In order to choose the best weight distribution hitch, you will first need to know your total tongue weight (TW), which is the tongue weight of your fully loaded and ready to go trailer plus the weight of any cargo behind the rear axle of your tow…

view full answer...

Answer 3

The tail lights are the easiest way to distinguish which style of body you have for your 2007 GMC Sierra 1500. From the description you gave me it sounds like your son has the New Body style. If you check out the attached picture you can see that the…

view full answer...

Answer 4

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 5

I looked up the towing capacity of a 2007 Chevy Silverado 2500 with a 6.0 and every configuration was well over 7,600 lb so yes it could. Looks like lowest configuration is 9,600 lb towing capacity and highest 13,000 lb. I'd recommend confirming…

view full answer...

Answer 6

The retracted height of this product #BD0287600300 is 29-1/2", the ball hole is 2-5/16", and has a range of adjustment of 8".

view full answer...

Answer 7

The outer diameter of the outer tube on the Bulldog Gooseneck Coupler part #BD0287600300 is 4-1/2" diameter.

view full answer...

Answer 8

I do have a solution for you, however the B&W Companion 5th Wheel Trailer Hitches like the Sliding #BWRVK3400-5W are not compatible with the Curt Gooseneck Hitch installed on your 2015 Chevrolet Silverado 2500. As you noted, the B&W uses a…

view full answer...

Answer 9

To install a fifth wheel hitch that would be compatible with your existing Curt gooseneck hitch, I'd recommend using Curt X-5 adapter, part #C16210. This adapter will lock into a Curt Double-Lock, Flip and Store gooseneck hitches (C-60 and C-600…

view full answer...

Answer 10

You can definitely connect a 5th wheel wiring harness to the bumper 7-way on your truck. The second in-bed 7-way connection is simply to give an easy access point and clean look. It keeps the wiring from dragging or moving against your tailgate, so…

view full answer...

Answer 11

As far as function goes, the two controllers are actually pretty similar. The primary difference between the two is that the P3 uses what I would call a more user friendly display. Instead of an error code like what's displayed on the P2, the P3…

view full answer...

Do The Hitch Ball Holes Line Up On a Curt EZr and B&W Turnoverball for a 2005 GMC Sierra

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching