Mounting Bracket Bolt Hole Dimensions of the Extreme Off-Road Trailer Jack w/ Dual Wheels # ORJW500D

Question

Question:

Hi, can you pls provide the mounting plate dimension for this jack? They seem to be huge and wanted to make sure about the dimensions. Thanks!

asked by: Humprey

0

Expert Reply:

I spoke with my contact at Ark and he sent me a dimensional drawing of the mounting bracket that the Extreme Off-Road Trailer Jack w/ Dual Wheels # ORJW500D has. The dimensions are in millimeters.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Here is an image I have from the Xtreme Off-Road Swing-Up Trailer Jack #ORJW750D in zinc which will have the same dimensions as the black Jack #ORJW750BD you are looking at.

view full answer...

Answer 2

The correct Lock N Roll hitch assembly is going to depend on the size of the channel the coupler of your trailer sits on. You need about a 5" drop, and the closest is going to be the 4-1/2" drop Lock N Roll Articulating Hitch for 2"…

view full answer...

Answer 3

For your 2.5 inch wide and 2 inch high trailer tongue, the Round Swivel Marine Jack w/ Wheel - Bolt On - Zinc - Sidewind - 11" Travel - 1,500 lbs #MJ-1500B is my recommendation. It will work very well with the trailer tongue you have and will…

view full answer...

Answer 4

When folded up and traveling the Xtreme Off-Road Ratcheting Trailer Jack item #ORJW750BD is 29" long from the top of the jack to the bottom of the wheels. From the bottom of the wheel to the center pivot point where the bracket attaches is…

view full answer...

Answer 5

Yes, the Extreme Off-Road Swing-Up Jack w/ Dual Wheels iItem #ORJW500D will work for your T@B 400 Tear Drop Trailer. It looks like your trailer comes with an a-frame jack. You would need to ensure you have enough space on your tongue to accommodate…

view full answer...

Answer 6

A 3,000 lb jack would be able to lift a 5,000 lb trailer since the jack would basically only be lifting half of the trailer weight since the other half is supported by the wheel on the other side. I think bare minimum you'd need a 2,500 lb jack…

view full answer...

Answer 7

I will start by saying the ARK Extreme Off-Road Ratcheting Trailer Jack w/ Wheel #ORJW1SU will fit frames that are 2" to 6" tall. The bolt hole measurements vary and I included a diagram with everything listed, but the overall dimensions of…

view full answer...

Answer 8

The collapsed height of the Extreme Off-Road Ratcheting Trailer Jack w/ Wheel #ORJW1SU is 28-5/8" from the base of the wheel to the top of the jack tube. The tallest measurement of the jack when fully extended is 31-15/16" from the center…

view full answer...

Answer 9

The Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels, #ORJW350D has an overall length of 18".

view full answer...

Answer 10

I was able to have our warehouse measure the mounting plate for the Ark Extreme Off-Road Swing-Up Trailer Jack #ORJW350D you were looking at and included a diagram showing its dimensions. The Ark #ORJW350D mounting bracket measure 7-1/2" tall x…

view full answer...

Answer 11

I have included an image below with the measurements for the mounting plate on the Xtreme Off-Road Ratcheting Trailer Jack #ARK54FR. The hole to hole measurements are from center of hole to center of hole.

view full answer...

Answer 12

If you are needing your trailer frame to be 23" from the ground to the top of the frame then I recommend going with the Extreme Off-Road Trailer Jack w/ Dual Wheels #ORJW500D with the 18-3/8" lift because the part #ORJW350D with the…

view full answer...

Mounting Bracket Bolt Hole Dimensions of the Extreme Off-Road Trailer Jack w/ Dual Wheels # ORJW500D

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching