Air Compressor and Tank Recommendation for Air Horn Installation

Question

Question:

Could this compressor be used to power an airhorn or is a tank needed for that?

asked by: George

0

Expert Reply:

You're going to need a compressor with an air tank of at least 2 gallons, so I recommend going with the Air Command II Xtreme Duty Compressor # F2549 . This comes with a 2 gallon air tank, compressor and wiring to install. If you wanted to go with a bigger air tank you could also purchase the Firestone 3 Gallon Air Tank with NPT ports # F9245.

expert reply by: Erik B

0

Answer 1

If you needed a kit that would run your air accessories, inflate tires, and keep constant pressure in air bags you'd need two separate compressor and tank setups. Or you could use the Air Compressor - 145 psi #F2549 that you mentioned for both…

view full answer...

Answer 2

So there is an option for a compressor that will let you fill up your tires as well, but the wireless Air Lift WirelessAIR Compressor System for Air Helper Springs #AL74000 doesn't have that capability. There aren't wireless options for a…

view full answer...

Answer 3

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 4

For towing your fifth wheel with your Ram 2500 4x4 you can't go wrong with a set of Firestone air bags. The Firestones are a great air bag and my go to when it comes to suspension enhancements period. When using these air bags versus the other…

view full answer...

Answer 5

Yes, the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs #F95FV are compatible with your 2020 F-350 DRW FX4. Check out the video linked below for more details on this product.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Hi Joe, Yep, you heard correct, you can go from a 2 inch shank to a 2-1/2 inch shank with your Reese weight distribution hitch without issue. One of the following 2-1/2 inch shanks should have the right rise/drop for your application. Here are the…

view full answer...

Air Compressor and Tank Recommendation for Air Horn Installation

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching