What is Typical Size for RV Screen Door Sliders

Question

Question:

Im looking for sliders for the entry door of my 03/04 Jayco Qwest 10x pop up camper. I need both the upper and lower sliders. So you have one that fits this specifically or is there a universal one?

asked by: Ron B

0

Expert Reply:

A pretty standard rv screen door slider dimension is right at around 12 inches like the part # LC234101 which most likely would work for you, but the best way would be to measure the slot dimension you have so you can verify what would be the correct size to fit.

I attached a link to all of the sliders we offer if you need a different size.

expert reply by: Jameson C

0

Answer 1

RV makers typically do not keep track of smaller items like the screen door slides they install in their travel trailers like your tandem axle 2012 Crossroads RV Sunset Trail Reserve 26BH. I wish I had a way to look up this part of the trailer for…

view full answer...

Answer 2

The adjustable frame clamps on the Hollywood Racks Destination Bike Rack #HLY94FR allows for you to carry women's bikes or hybrid framed bikes without needing an adapter. The Frame clamp can be lowered to the clamp to the frame on both bikes. I…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey David, we've used the LaSalle Bristol RV Roof Vent install kit part #344270KITW to install several MaxxFan RV roof vents and it's worked well so it would also work well for you. This comes with everything needed so it would be a great…

view full answer...

Answer 5

We do have the panels separately. What you're looking for is the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182.

view full answer...

Answer 6

Yes, the lid is available as a replacement part. Based on the part numbers you gave me the correct replacement lid is the #FVK1020-19. For the lift arm you can use the #FVK8011-05.

view full answer...

Answer 7

We have direct replacements for the two brake assembly part numbers you listed. You would want part #AKEBRK-35R and #AKEBRK-35L. Or, for never adjust assemblies the part #AKEBRK-35L-SA and #AKEBRK-35R-SA would work as well. Most likely you have a…

view full answer...

Answer 8

You are correct that the original part has been discontinued. The replacement seat #DOM25FR (385343831) is going to be your best bet. It looks like your current seat is about 14" or 14-1/2" across and about 16" long. The replacement…

view full answer...

Answer 9

The best replacement option for your 36.5" wide x 16" tall cutout hole is going to be the Furrion Electric RV Fireplace with Crystals #FF40SC15ABL. This unit would have to be 'wall-mounted', which means that only the smaller body…

view full answer...

Answer 10

The great thing about these sliders like the Lippert Components Bubble Slider #LC234101 , which is 12" x 12" is that they can be trimmed down as needed. In order to make any necessary changes to these sliders I would first make a test fit…

view full answer...

Answer 11

2020 and newer GM trucks use pulse width modulation which won't send enough power to properly operate a Furrion RV camera system. To solve this Furrion came out with the #FR87PR which corrects the problem by looping over power from the 12v…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...