Should Curt Trailer Hitch Be Crooked on 2019 Ram 1500 Classic
Question:
Hey there. So I just finished installing this hitch SUPER easy!. It is just slightly crooked when looking down at it from above - not very much but just a hair. This is a new truck with no accidents. Is it normal for it to be a bit crooked at first? The way the bolts tighten it to the bumper frame doesnt appear to allow it much play if I loosened it up and tried to correct it. It seems like it would just pull it back out of alignment. Thanks!
asked by: Andy A
Expert Reply:
The Curt Class IV Trailer Hitch # 14374 really shouldn't look crooked when mounted to your 2019 Ram 1500 Classic. The frame brackets on each side of the hitch are of an equal height so unless something was off on the frame rails of the truck the hitch should appear level.
You can certainly try loosening up a couple bolts and re-tightening them to make sure everything is secure. I know it sounds silly but also make sure the truck is parked on completely level ground when examining the hitch.
If the hitch still looks this way after tightening down the hardware please let me know. Please also feel free to email me a picture of the trailer hitch directly and I can take a look to see what might be causing it.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 1000 lbs TW
- 10000 lbs GTW
- 12000 lbs WD GTW
- 2 Inch Hitch
- 1200 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Q&A: Best Trailer Hitch for a 2024 Subaru Forester
- Shop: Trailer Wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Choosing the Right Trailer Wiring
- Video: Tekonsha T-One Vehicle Wiring Harness Installation - 2022 Subaru Forester
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Search Results: 2 inch ball
- Video: etrailer Rubber 2" Hitch Cover Review
- Video: Tekonsha Custom Fit Vehicle Wiring - Trailer Hitch Wiring - 118470 Review
- Shop: Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Hopkins Plug-In Simple Vehicle Wiring Harness Installation - 2020 Acura MDX
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Curt Class III Trailer Hitch Installation - 2021 Subaru Forester
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Curt Trailer Hitch Installation - 2020 Acura MDX
- Search Results: backup lights
- Shop: Performance Chip Tuners
- Shop: Floor Mats
- Shop: Vehicle Lights
- Search Results: lights
- Search Results: reverse lights
- Q&A: How to Install Trailer Hitch on Vehicle with Stripped Weld Nut
- Q&A: Is it Important to Use all of the Installation Bolts When Installing a Curt Hitch
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Troubleshooting B&W Companion Hitch Leaning to One Side When Connected to Trailer
- Q&A: Adjusting the Angle of the Head on an EAZ Lift Weight Distribution System
- Q&A: Is it Normal for 5th Wheel Hitch Head to Lean Over to One Side When Not Hitched to Trailer