Can I Replace Hand Winch With ATV Winch On Jack Rack Hoist

Question

Question:

Can you replace the manual winch with an ATV 2500 lb winch. Winch weighs about 15 lbs. Only need to lift kayak to top of trailer 50 lb.

asked by: Kurt W

0

Expert Reply:

It is possible to replace the winch on your Viking Solutions Rack Jack II Hoist part # 310-VRJ001 with an ATV winch like part # CU122390. ATV winches are rated for horizontal pull not to lift or hoist however, I did contact ComeUp (one of our winch manufactures) and they said since all you are using it for is to lift a kayak you would be okay to mount it to the Rack Jack. Please keep in mind the ATV style winches are not made to lift so I would not lift anything heavier than your kayak with it attached to the Jack Rack.

expert reply by: Heather A

0

Answer 1

For loading 75 lb. ebikes, the Viking Solutions Rack Jack II Hoist with Winch for 2" Hitches, #310-VRJ001 would be sufficient. I don't see the need for the larger hoist, #310-VMH001. We have available the Westin Truck-Pal Fold-Up Bed…

view full answer...

Answer 2

The Air Lift WirelessONE Compressor System for Air Helper Springs - Remote - Bluetooth - EZ Mount #AL25980EZ does not have components for manual inflation if the compressor somehow doesn't work, but we do have options for you. While I would…

view full answer...

Answer 3

The Viair Portable RV Air Compressor Kit #VA39WR does not give you the ability to set the compressor to a specific PSI. The compressor features an on/off switch on the compressor to shut it on and off otherwise it will continue to run unless the…

view full answer...

Answer 4

Let's start with the hoist to remove the B&W Companion 5th Wheel Hitch #BWRVK3600 from your Ram 2500 and you can absolutely use the B&W 5th Wheel Lifting Device #BWRVXA3130 with the Viking Solutions Rack Jack II Hoist with Winch for…

view full answer...

Answer 5

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

For your 2020 Chevy Silverado 2500 short bed with the factory puck system I highly recommend the B&W OEM Companion Slider #BWRVK3775. I like an awful lot about this particular hitch but some of the features that really stand out are its 1"…

view full answer...

Answer 8

The B and W Patriot Hitch part #BWRVK3270 does not require a capture or locking plate to connect to fifth wheel trailer. The only hitches that do that are the ones that are auto-sliders where the head of the hitch locks to the pin box and turns with…

view full answer...

Answer 9

Yes, the #100019-24 pigtail can be used to connect your dual-cylinder 100 lb propane setup to the regulator on your RV. Since this hose does not have a back-check to contain a gas leak, you will need the #204120-MBS fitting that includes a…

view full answer...

Answer 10

In order to find the correct replacement leaf springs for a 2020 Grand Design Reflections 337RKS, you'll simple need to measure their length, unloaded, from the center of each eye. I recommend going with the Double-Eye Spring for 6,000-lb Trailer…

view full answer...

Can I Replace Hand Winch With ATV Winch On Jack Rack Hoist

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching