What are the Dimensions of the Thule Square Bars

Question

Question:

What is the square dimension measurements/

asked by: Joe

0

Expert Reply:

I went out into our showroom and measured the dimensions of a set of discontinued Thule square load bars and found that they are 7/8 of an inch by 1-1/4 inches. This is identical to the Inno square bars like # INB137.

expert reply by: Jameson C

0

Answer 1

The longest load bars we have that will fit the older style of Thule square bar feet is 79 inches with the Inno #IN436L.

view full answer...

Answer 2

If you are not experiencing sag then you can start with just the Reese Friction Sway Control Kit part #83660 and the Reese Sway-Control Bracket for 2&quot; Ball Mounts part #RP26003. There is no good way to attach this other than welding to…

view full answer...

Answer 3

The INNO square bars are the same shape as the older Thule square crossbars that didn&#39;t have the channel that ran on the underside of the bar. So for a longer crossbar setup you could use the part #IN436L for a 79 inch bar.

view full answer...

Answer 4

The Thule Podium 460 you referenced for old square bars has been discontinued so that is why the expert answers suggest using the Evo Fixpoint Feet #TH49SC for use with the new Thule SquareBar that have a slot in the bottom like the aero style…

view full answer...

Answer 5

Great News! The Thule Hull-A-Port XT Kayak Carrier TH848 is 100 percent compatible with the Malone AirFlow2 Roof Rack systems like part #MPG216. The Hull-A-Port uses the clamps on the bottom which will grab a hold of the Malone bars for an…

view full answer...

Answer 6

The differences between the Yakima HoldUp #Y02443-2 and the HoldUp EVO #Y02479-2 include an integrated SpeedKnob to take out movement of the bike rack, an easier system for tilting the bike rack, and the ability to add fat bike tires (up to…

view full answer...

Answer 7

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 8

For your 2018 Honda HR-V to be compatible with the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs #TH898, you have to use slightly longer crossbars. The Hullavator requires 4-8 inches overhang to give clearance. In order to give…

view full answer...

Answer 9

The Curt Roof Rack for Raised Side Rails - Aluminum - Black - 53-3/8" Long #C18118 can be used with the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs - Side Loading #TH898 on your 2018 Toyota 4Runner. Often people use…

view full answer...

Answer 10

Yes. Since the Inno Square Crossbars #INB147 have the same dimensions as the Thule SquareBar Evo Crossbars #TH712300 (7/8" tall x 1-1/4" wide), the Inno Square Crossbars will fit the Replacement Railing Foot for Thule Tracker II…

view full answer...

Answer 11

Based on the photos you sent me, it looks like you are talking about Replacement Upright Bar Bracket #1500052940. This is the upright bracket for Thule ProRide XT #TH598004 and Thule ProRide XT #TH598004-FB. I have attached a photo of the Thule…

view full answer...

Answer 12

Since your Thule Hullavator #TH898 was made in 2017 that means that it is one that can be used on a Yakima roof rack for a naked vehicle roof like the Corebar #Y00422, #Y28TR, and #Y06135 which is a 60 inch crossbar setup and would easily be long…

view full answer...

What are the Dimensions of the Thule Square Bars

Product Page this Question was Asked From

Continue Researching