Where Should Camper Trailer be Jacked Up From to Change Wheel

Question

Question:

I have a 2018 geo pro 19fd. Wher do I place the Jack to lift the trailer

asked by: Tim C

0

Expert Reply:

You'd want to jack your 2018 Geo Pro 19FD up by the frame of the trailer or by the axle with a bottle jack like the Powerbuilt Unijack part # ALL620471.

I attached a review video for this jack for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Only Trail Boss would be able to get you a manual for your trailer. You'd need to use a bottle jack like the #ALL620471 to jack up the trailer by the frame to change the spare.

view full answer...

Answer 2

The Powerbuilt Unijack Bottle Jack with Built-In Jack Stand - 21" Lift - 6,000 lbs #ALL620471 is the solution for both of your questions. You should use two of these to lift your ATV level. The scissor jacks for RV's are only support jacks…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hey Michael, thanks for reaching out! The Timbren Active Off-Road Bumpstops #T28GR you installed on your 2018 Ford F-150 unfortunately have that reputation among users (although Timbren claims their systems provide a smooth ride). Because of this we…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The correct Roadactive kit that fits your 2023 Ford F-150 is the part #RAS3611-YHD. I really like the RAS kits as they basically don't have any downsides. You get the adjustable support, an easy install, no maintenance, and actually improves…

view full answer...

Answer 11

The Electric Jack w/ Footplate and 7-Way Plug #EJ-3527-BBX uses a 7-way RV-style plug. I have included a diagram that shows the pin-out for RV style 7-way plugs. This will show you what each pin does. I have also listed the functions below and linked…

view full answer...

Answer 12

According to RoadActive Suspension the spring rate for the standard kit #RAS3611-S is 2,400 lbs. For the heavy duty #RAS3611-SHD it is 3,600 lbs. The heavy duty #RAS3611-SLHD is the same but only designed to fit if you have factory top overload…

view full answer...

Where Should Camper Trailer be Jacked Up From to Change Wheel

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching