Difference Between Curt Class III Hitch # 13534 and Draw-Tite Max-Frame # 75586
Question:
What is the difference between the Curt trailer hitch receiver costom fit class III -2inch and the Draw-tite max trailer hitch recevier costom fit Class III - 2 For toyota highlander sport 2008
asked by: Joe D
Expert Reply:
Both the Curt Class III Hitch Receiver # 13534 and the Draw-Tite Max-Frame Trailer Hitch # 75586 are confirmed to fit your 2008 Toyota Highlander Sport and feature 2 inch receivers that will sit pretty much in the same location beneath the rear bumper on the vehicle.
There are a few differences between the two models other than the brand name and this is one of those cases where the best unit will depend on your specific application and what your Highlander is equipped with.
The Draw-Tite Max-Frame # 75586 will be your best option if you plan on mostly using the hitch to secure accessories like a bike rack or cargo carrier. This is because unlike with the Curt model, Draw-Tite does not require the use of additional support straps when attaching non-trailer loads. These can be a bit of a pain to install and it's something that Curt requires on this particular hitch to maintain its warranty. The receiver on the Draw-Titch will also sit just slightly further towards the rear of the vehicle which simply makes it easier to attach and remove a bike rack or cargo carrier.
The Curt Class III Hitch # 13534 is what you will need though if your Highlander is equipped with the full size spare tire beneath the vehicle. This is because the Curt hitch will allow you to keep it in place while the Draw-Tite would require its removal to make room for the brackets. The Curt hitch is also made right here in the USA and has a slightly higher tongue weight capacity of 750 pounds (compared to 500 pounds on the Draw-Tite).
Both hitches have identical 5,000 pound towing weight capacities.
I have attached an installation video for each trailer hitch as well that you can take a look at.
Products Referenced in This Question
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: 2023 Best Gifts for Haulers & Towers
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Recommended Flat Towing Components For A 2024 Chevy Trax
- Article: Slipper Spring Trailer Suspension System Review
- Q&A: Best Ground Clearance Hitch Receiver for Carrying a Bike Rack on a 2013 Toyota highlander
- Article: Roadmaster Tow Bar Feature Descriptions
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Recommended Hitch for a 2024 Volvo XC90 Recharge
- Q&A: Does Thule UpRide Bike Rack Fit 2022 Subaru Outback Factory Roof Rack
- Q&A: Will Thule Upride Roof Bike Rack Fit 2012 Toyota Highlander with Factory Crossbars
- Q&A: Is the Finish on the Tow Ready Trailer Hitch Ball # 63853 Shiny or Dull
- Q&A: Bike Rack for 2013 Toyota Highlander That Allows Rear Hatch Access
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs