Replacing Gears for etrailer.com and Ram Jack TJD/TJDA-5000S
Question:
INTRO TO QUESTION: Thank you for explaining that the gears for TJD/TJDA-5000S are the same as for TJD-7000S-GR which is gear kit TJA-2000S-GR. Thanks also for directing me to watch your video for rebuild of TJD-7000S-HD... Yet, I cannot find video or pictures showing rebuild or inside views for TJD/TJDA-5000S. 2 QUESTIONS 1. Can TJD/TJDA-5000S be rebuilt using TJA-2000S-GR kit without special tools, cutting, or modifying the stock unit? 2. Are any videos/pictures available to assist in such a rebuild of TJD/TJDA-5000S?
asked by: Matthew C
Helpful Expert Reply:
The Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 15-1/4" Travel - 3,000 lbs # TJDA-5000S does not currently have any inside photos or videos I can share.
The Replacement Gear Kit for etrailer and Ram Sidewind Jacks - 2,000 lbs and 5,000 lbs # TJA-2000S-GR will only work on round jacks and the Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 7,000 lbs # TJD-7000S-GR is what is needed for square jacks and some round jacks with the different square head unit. I've attached videos to assist as your disassembly and repair will be very similar. The number of teeth in the gears and the size of the gears are different so don't be thrown by the names of the products. I confirmed with the manufacturer the # TJD-7000S-GR is what you need for your jack.
There are not any special tools needed for your repair and there won't be any modification needed to the stock unit. There is no cutting involved, you will just need a screwdriver to remove the cap, a mallet or hammer to help drive out the roll pins, a small screwdriver or pick to allow you to just get the roll pin, and a needle nose pliers to hep pull it.
Products Referenced in This Question
Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 5,000 or 7,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Gears
- etrailer
more information >
Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- Steel
- 2001 - 3000 lbs
- Sidewind Jack
- 29 Inch Lift
- Bolt-On
- With Rectangle Foot
- etrailer
more information >
Product Page this Question was Asked From
Replacement Gear Kit for etrailer and Ram Sidewind Jacks - 2,000 lbs and 5,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Gears
- etrailer
more information >
Continue Researching
- Q&A: What Is The Thickness Of The Replacement Gear Kit For Etrailer And Ram Sidewind Jacks
- Q&A: Replacement Zerk Fitting Recommendation for Dexter EZ Lube Spindle
- Q&A: How To Mount The Furrion Chill Replacement For RV Air Conditioner for Dometic Brisk Setup
- Article: Pintle-Hitches
- Q&A: Dimensions of Gear Kit for etrailer and Ram Sidewind Jacks
- Q&A: Breakaway Switch Recommendation to Replace a Bargman Breakaway on a 1976 Nomad Trailer
- Q&A: Is the Replacement Motor for HappiJac 4820 Camper Jacks Available in Black
- Q&A: Can the HappiJac 4820 Motors Fit On Older 4800 Series Jacks?
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Article: Best Bike Racks for Electric Bikes
- Article: Best Boat Trailer Jacks
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps