Correct Cover for Roadmaster StowMaster 5000 Tow Bar

Question

Question:

I would like to purchase a cover for the above model tow bar remains on car after disconnect but can’t tell which one fits my system. Advice please. Thank you

asked by: Kathryn G

0

Expert Reply:

The correct cover for your Roadmaster StowMaster 5000 Tow Bar is the Roadmaster StowMaster Tow Bar Cover part # RM-052-3. There is no difference between the Roadmaster StowMaster Tow Bar part # RM-501 and the Roadmaster StowMaster 5000 Tow Bar that you have.

expert reply by: Conner L

0

Answer 1

The Roadmaster StowMaster Tow Bar - Car Mount - 2" Ball - 6,000 lbs #RM-501 is a universal fit for any vehicle that is under 6,000 lbs curb weight and has Roadmaster EZ, EZ2, EZ4, XL, and Classic vehicle-specific base plates. The Roadmaster MX,…

view full answer...

Answer 2

It does look like it's time to replace the tow bar cover! I went to the warehouse and measured the Roadmaster StowMaster Tow Bar Cover part # RM-052-3 it measures 3'8" and about 7" deep so you should not have any issues using this…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Correct Cover for Roadmaster StowMaster 5000 Tow Bar

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching