Replacement Control Panel for Atwood Water Heater

Question

Question:

90098 is the PN on the side of the controller. What is the correct replacement part. This is a gas only water heater. Thanks.

asked by: Bob J

1

Helpful Expert Reply:

I reached out to my contact at Dometic, who took over Atwood's water heaters and the control panel you need is the one you were looking at, part # AT91367.

expert reply by: Charles S

1

Answer 1

I was able to find out from Dometic, who took over Atwood's water heater division and the Replacement Control Panel #AT91367 you were looking at will be the correct part.

view full answer...

Answer 2

The correct part to replace your current converter charger is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 55 Amp part #PD4655V. This is an exact replacement and will be all you need to get back operational. I have…

view full answer...

Answer 3

Yes, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 55 Amp, #PD4655V is what you are looking for. This upgrades or replaces the converter section for 55-amp Parallax/Magnetek, WFCO, or Parallax RV power centers and works…

view full answer...

Answer 4

No, The Replacement Lid for MaxxFan and MaxxFan Plus Roof Vents - White #MA10A40002K is not the correct cover you will need for your Maxxair 4700G. The correct cover you would need is The MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer…

view full answer...

Answer 5

I was unable to find any reference to the numbers you listed, but based on the dimensions you gave my best guess is you need the MaxxAir Replacement Shroud for Coleman-Mach / RVP Brand RV Air Conditioners #MA8335A5261. This is for older…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Replacement Control Panel for Atwood Water Heater

Product Page this Question was Asked From

Continue Researching