Replacement Shroud and Roof Vent Recommendation for a Coleman Mach 6727-731 AC Unit

Question

Question:

The model number on my rig’s Coleman Mach AC is 6727-731. I need to replace the exterior shroud as it’s about to fly off only the rear two bolts holding it on. Do you carry replacement shrouds to fit this and the bolts needed? I’ve tried to find the strange “L” shaped bolts everywhere locally but no one has them. Second question is, I eventually want to remove this AC and install another vent fan in it’s place Fan-tastic or MaxAir is there a particular make/model of vent fan you would recommend for this application? My two main criteria are 1 Low exterior profile, and 2 reversible airflow. Thanks for your time and consideration!

asked by: Catherine

0

Expert Reply:

The only replacement shroud that will work with your Coleman Mach AC is 6727-731 that we have to offer is the MaxxAir TuffMaxx Replacement Shroud # MA00-325001. This is compatible with Coleman-Mach Mach 1, Mach 3 and Mach 15 models. It comes with washers and nuts to mount it but unfortunately it doesn't come with the "L" shaped bolts that you mentioned.

If you are looking for a lower profile vent to replace your current AC unit then you want to go with a MaxxAir vent as they sit lower than the Fan-Tastic vents. Out of the MaxxAir options we have the MaxxFan Plus Roof Vent # MA00-04500K which features a power lift, the reversible air flow, and sits 3-3/4" tall when closed but 12-1/2" tall when fully opened. We also carry the MaxxFan Deluxe which sits 5" tall when closed but only 9-5/16" tall when fully opened. It not only has the reversible fan function but it also includes a built-in rain shield and is available with a manual lift # MA00-06200K or powered lift # MA00-07500K.

Attached are some review videos for you to check out as well.

expert reply by: Jon G

0

click to enlarge

Answer 1

I do have a solution, but unfortunately the backing plate with the license plate holder is not available as a replacement part. The only option is to replace the light completely. If you want to stick with the black you need the #RVSTLB61 or for…

view full answer...

Answer 2

I do have an option for you but the wraparound style taillights on a 2000 Jayco Eagle Camper are no longer available therefore your only options for replacement are changing to a different style like the Low Profile LED RV Tail Light part #RVSTLB60…

view full answer...

Answer 3

There is not a direct replacement for your series 6300A model 6325 power converter. The 25 amp converter with 12V power can be replaced with the Progressive Dynamics Inteli-Power RV Converter and Battery Charger - 12V - 30 Amps #PD9130 which will…

view full answer...

Answer 4

Both the Jensen JWM6A and the current model, part #JWM62A are classified as double-DIN head units, which will both use the same sized rough openings in a vehicle dash. The old #JWM6A and the current model #JWM62A both use the same pigtail, as you can…

view full answer...

Answer 5

There are three types of hinges for replacement roof vents: 3 point, 4 point, and continuous. Replacement #BV0534-00 has a closed round hinge, which is continuous. It sounds like you need either a continuous hinge that is not closed such as…

view full answer...

Answer 6

Sounds like you are trying to replace the cable on the breakaway switch of your trailer. If you are trying to pull the plunger out you would not need to put any current on any of the wires to get the plunger to release. It is pretty hard to release…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Can you email me the pictures? Its going to be one of the following two though. Either part #MA00-325001 or #MA8335A5261. Whichever looks like what you have would be correct.

view full answer...

Replacement Shroud and Roof Vent Recommendation for a Coleman Mach 6727-731 AC Unit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching