Removing and Reinstalling New Retainer Pins in Fastway Weight Distribution System

Question

Question:

how to replace round bar release clip

asked by: Dorsey K

1

Helpful Expert Reply:

First you have to get the lower screw out of the head of the system. Since the screws don't have a slot or Philips head on them you'll have to pry them out some have to use a chisel. Once they are out you'll slide the clip down so that it will pass through the hole in it. You'll then have to pry out the top pin as well. To install new one you'd reverse the process.

expert reply by: Jameson C

1

click to enlarge

Answer 1

We currently have the Spring Bar Retainers from Curt #17109 and Fastway #FA94-02-1059.

view full answer...

Answer 2

We have a few different clip options that are possible fits for your Weight Distribution (WD) system. Fastway WD - FA94-02-1059 Curt WD - 17109 From the picture that you sent me, I believe that the Curt clips #17109 are the correct replacement…

view full answer...

Answer 3

Sounds like you are looking for the Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars #FA94-02-1059 which is the correct release clip for the Fastway e2 round bar weight distribution systems.

view full answer...

Answer 4

As far as I know this is not a common problem, and not something that we have had reported as an issue for the #FA94-00-1000. It is important to make sure that everything is secure when installing the weight distribution hitch. The spring bars…

view full answer...

Answer 5

It sounds as if you're needing the spring bar retainer clip kit. If you have the Curt or a Reese Round Bar system, use #17109 which includes 2 clips, 2 lock pins and two drive-in rivets. The exact kit needed will depend on which…

view full answer...

Answer 6

Brent, to remove the Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars #FA94-02-1059 you are going to need to start by getting the lower screw out of the clip which you're going to need to pry…

view full answer...

Answer 7

It sounds like you might need the clips that hold your round spring bars in the head unit. If you have a Fastway e2 system then their Replacement Spring-Bar Release Clips #FA94-02-1059 are the correct part. If you have a Curt system use their part…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Doug, thanks for reaching out! The MORryde ALLTREK 4000 #MR89DR dimensions can be a bit difficult to explain via text so I've attached an image giving you the dimensions you're asking about!

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Removing and Reinstalling New Retainer Pins in Fastway Weight Distribution System

Product Page this Question was Asked From

Continue Researching