Correct Slide-Topper for a Box Width of 151-1/2 Including the Flanges

Question

Question:

My awning is 151.5 inches overall flange included. Is 13 foot correct size?

asked by: Billy

0

Expert Reply:

Yes, the correct Solera Slider (Slide-Topper) for your 151-1/2" measurement (including the flange) is the 13' part # LCV000165061. This is compatible with boxes that have a width of 146" - 151-3/4" which includes the measurement that you took.

We also offer this awning in white as part # LCV000163299.

expert reply by: Jon G

0

Answer 1

When choosing the slider you want to measure the outside front of box width including the flange. Then you need to select a slider that extends a minimum of 2-1/2 inches beyond each side of the box width. For example, the Black Solera Slider…

view full answer...

Answer 2

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 3

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 4

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 7

Most critical to trailer tire performance and durability are 1) proper inflation 2) observance of the tire's rated load capacity and 3) observance of the tire's speed rating. If either of these factors is off the mark then the tire will tend…

view full answer...

Answer 8

I'm pretty sure you are correct that the Coil SumoSprings Custom Helper Springs #CSS-1145R will fit your 2018 Toyota Highlander, however, we haven't had the chance to test this out and SuperSprings doesn't have this listed in their…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Answer 11

We only have the products listed on our website. I just double-checked to see if there was anything matching your descripton. The 4 microwave/convection/OTR ovens are all well over your 24" wide location. One of the smallest is the Furrion…

view full answer...

Answer 12

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Correct Slide-Topper for a Box Width of 151-1/2 Including the Flanges

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching