Is Replacement Handle for Bladex and Valterra Waste Valves Threaded

Question

Question:

My vehicle is a 2017 Coachmen Freelander. Its the inital blade valve below black water tank. The handle has lost one side. Is the handle a screw on/off?

asked by: Gerald H

0

Expert Reply:

The replacement water tank valve handle part # T1003-6NVP is threaded so it would fit as a replacement for you as long as shank is threaded as well.

expert reply by: Jameson C

0

Answer 1

You will need to select the correct waste valve handle based on your waste valve. Replacement Handle for LaSalle Bristol Cable-Actuated RV Waste Valves #34490CMA1 Replacement Handle for LaSalle Bristol Waste Valves #34466IHANDLE Replacement Handle…

view full answer...

Answer 2

Yes, the Black Handle #34466IHANDLE and Gray Handle #34466IHANDLEGRY will unscrew from the Bristol Double RV Waste Valves #34466ND14AAR. This will allow you to add the extension you need to make the handles easier to reach. 6" Extension…

view full answer...

Answer 3

Replacement waste valve handles will only work with their same manufacturer, so I'm not 100 percent sure which you have on your Cougar trailer, but a replacement handle simply needs to be one that matches the manufacturer of your waste valve. If…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Is Replacement Handle for Bladex and Valterra Waste Valves Threaded

Product Page this Question was Asked From

Continue Researching