Bearings and Seal Recommendation for Dexter 3,000 lb Axle

Question

Question:

Hi I need wheel bearings, seals, And eventually breaks For a 99 Coleman Fleetwood popup trailer Have attached a picture of the axle stamp maybe that will help any info would be great

asked by: Tom L

0

Expert Reply:

Thanks for the picture of the tag on your Dexter trailer axle. From that I can tell you have a 3,000 lb Dexter axle.

There isn't a kit available, but I was able to find each of the components you need, which are available individually. You will need bearing # LM67048 and matching race # LM67010, along with bearing # L44649 and matching race # L44610.

For a grease seal you need # 58846, along with grease cap # 21-41-1 and cotter pin # 165649.

For replacement brake assemblies you'd then want the part # K23-472-473-00 for both.

expert reply by: Jameson C

0

Answer 1

You really could use either one of the 68" #Y01158 or 78" #Y01159 bars, but I have a feeling that the 78" bars are going to stick out a little bit too far, so I do recommend going with the 68" Yakima HD Bars…

view full answer...

Answer 2

I checked directly with Yakima, and the shortest crossbar size for the OverHaul HD ladder rack on a 2021 Ford F-150 is indeed the 68 inch bars, and they say the 60 inch bars will not fit as they are too short. So the correct fit for your…

view full answer...

Answer 3

The correct bearings, races, and seals for your 2021 Grand Design Imagine XLS 17MKE is the Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles part #BK2-100.

view full answer...

Answer 4

I really wish there was a way to determine what bearings a trailer needed without actually pulling the wheel off and checking, but there isn't. The only two solution I have for you would be to remove the hubs and get the numbers that are…

view full answer...

Answer 5

I spoke with my contact at Dexter regarding your model 3K7258 axle that you referenced in your question. He was unable to pull up any specific bearing information using this model number. If you can locate the axle serial number, which should be…

view full answer...

Answer 6

I do have a recommendation for you, however, Yakima does not make an adapter for the Yakima HullHound Kayak Saddles w/ Tie-Downs part Y04079 that will allow them to work with the Thule Xsporter Pro Adjustable Height Truck Bed Ladder Rack part…

view full answer...

Answer 7

Good news, we do have availability on those brake shoes. The part mumber for the 10" x 1-1/2" Electric Brake Shoe/Lining is BP04-65. The shoes are sold individually.

view full answer...

Answer 8

There is no need to unplug a brake controller when it's not in use and typically something like the Curt Reflex C51130 shuts off automatically after a certain time period-usually around 15 minutes. These won't drain your battery when sitting…

view full answer...

Answer 9

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 10

It sounds like you have a 3,500 lb axle based on the L68149 inner bearing and L44649 outer bearing you said you had therefore, the Double Lip Grease Seal part #58846 which measures 1.719" inner diameter and 2.565" outer diameter is what you…

view full answer...

Answer 11

That closest door latch we have to the dimensions you have now is the part #295-000015 which measures 5" wide x 4-1/2" tall x 1-1/2" thick. This could possibly work but if the cut out on the door is 6 inches wide it wouldn't work.

view full answer...

Answer 12

If the surface on the inside of the drum where the shoe pads make contact isn't smooth then a brake shop may be able to turn the drums. If that surface or the surface where the magnet makes contact (called the armature surface) is discolored then…

view full answer...

Bearings and Seal Recommendation for Dexter 3,000 lb Axle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching