Replacement Hold Down Springs and Pins for Electric Trailer Brakes

Question

Question:

Could you please tell me what spring bushings and spring sidebars are in my tralers electrical braking system. Cant find them anywhere. Thank you

asked by: Marie

0

Expert Reply:

It sounds like you are talking about the parts that hold the brake shoes down. These parts include hold down springs that have little caps on them through which the hold down pins are inserted.

We have kit # AKBRKR-SHD which will work with AxleTek, Dexter, Lippert (LCI), IAC, and AL-KO 10 or 12 inch brakes with shoed widths of 2 inches or 2-1/4 inches.

If you have different size brakes or you are talking about different parts let me know.

expert reply by: Michael H

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 4

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do is match up…

view full answer...

Replacement Hold Down Springs and Pins for Electric Trailer Brakes

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching