How to Pick Out Landing Gear Replacement for Fifth Wheel Camper
Question:
landing gear for1991 jayco eagle series 255 non electric
asked by: Eddy S
Expert Reply:
In order to pick out a direct replacement for the landing gear on your 2007 Desert Fox 38U we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Bulldog Tandem Landing Gear Set # BD500162. Either way this landing gear set would work well for you, you just might have to have the brackets of your trailer removed and then install the brackets of the # BD500162.
I attached a picture that shows the dimensions that this landing gear set would fit with.
The jacks would be the correct replacement for Lippert, Venture, and Atwood landing gear, as well as those from a few other manufacturers. The sure way to tell is that if the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) is 17-1/2 inches. If this is the case, the landing gear should fit just fine.
If your frame clamps are instead 20-1/4 inches the Ultra Fab part # UF17-943010 would be a direct replacement.
Products Referenced in This Question
Bulldog Tandem Landing Gear Set - Drop Leg - 36" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Bolt-On
- 2 Jacks
- Bulldog
more information >
Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- Landing Gear
- 38 Inch Lift
- Weld-On
- 2 Jacks
- Ultra-Fab Products
more information >
Product Page this Question was Asked From
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 5001 - 6000 lbs
- Electric Jack
- Landing Gear
- 35 Inch Lift
- Weld-On
- 2 Jacks
- Stromberg Carlson
more information >
Featured Help Information
Instructions
Continue Researching
- Video: Lippert Ground Control Replacement Leg Review
- Shop: Replacement 24-1/2" Left Rear Leg - Lippert Ground Control 3.0 Electric Leveling System
- Shop: Replacement 22-1/2" Left Rear Leg for Lippert Ground Control 3.0 Electric Leveling System
- Q&A: Where to Measure To Determine if Lippert Landing Gear Jack part # LG-1 Fits Trailer
- Q&A: How to Know if Stromberg Landing Gear # LG-1 Will Fit 2003 Montana Fifth Wheel
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
- Search Results: landing gear
- Q&A: Compatibility of Stromberg Carlson # LG1 Landing Gear with Lippert Fifth Wheel Frame
- Q&A: How Landing Gear Jacks are Connected to Fifth Wheel
- Q&A: Height of Outer Tube on Stromberg-Carlson Landing Gear # LG-1
- Q&A: Landing Gear Recommendation for 2008 Forest River Sierra 5th Wheel Trailer
- Shop: Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs
- Shop: LubriMatic White Lithium Grease - 14 oz. Cartridge
- Q&A: 5th Wheel Landing Gear Lead Jack Repair Kit Availability
- Shop: Replacement Aluminum Gearbox for Stromberg Carlson Landing Gear
- Shop: Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs
- Shop: Trailer Hitch
- Search Results: trailer jack
- Video: etrailer Landing Gear Set Review
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: awning
- Shop: Suspension Enhancement
- Search Results: e~track
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Search Results: etrack
- Shop: Fifth Wheel Hitch
- Search Results: lc142178
on Trailer Jack
