Measurements of Draw-Tite Trailer Hitch Receiver # 41920 for 1998 Ford Light Duty Pickup

Question

Question:

Trailer hitch # 41920 measurements

asked by: Ryan M

0

Expert Reply:

The Draw-Tite # 41920 is confirmed to fit your 1998 Ford Light Duty truck. I'm not sure which measurements you need exactly so I went out to the warehouse and measured the distances between each set of bolt holes, which you can see in the pictures I've attached. Also, it's 10-1/2 inches from lowest point to highest point.

I've also linked an install video for you.

expert reply by: Charles S

0

click to enlarge

Answer 1

For a 2004 Ford E-350 Cab and Chassis the Draw-Tite #41906 is a custom fit, but you will need to make sure that the bolt holes are 38-5/8 inches from frame to frame in order for it to fit your particular model. While this hitch is a custom fit for…

view full answer...

Answer 2

The overall width of trailer hitch #41906 is 41-1/2 inches. I have included a picture showing this and other measurements for the hitch. This is a custom fit hitch so if you have a 1992 to 2014 Ford full-size van (E series) then this hitch will fit.…

view full answer...

Answer 3

The distance between the horizontal mounting holes on the Curt Trailer Hitch Receiver #14055 you were looking at are 2-3/8" and 8" as shown in the included diagram. I included a video of the #14055 on a 2004 Ford Van for you to take a look…

view full answer...

Answer 4

You'll want to have a look at the van's rear frame are to determine if any features of your particular KUV utility body will interfere with the hitch or block any of it's attachment points. Since KUV bodies can extend back pretty far you…

view full answer...

Answer 5

I do have a possible solution for you but there aren't any aftermarket custom fit hitches that are confirmed to fit RV models on the 2016 Ford Transit T350. But take a look at Curt adjustable trailer hitch #C13702. This is essentially the same…

view full answer...

Answer 6

I would be happy to help! The Draw-Tite Trailer Hitch Receiver #41906 you were looking at measures 18-1/2" from the center of the rear mounting holes to the center of the hitch pin hole where the Curt Trailer Hitch Receiver #14055 measures…

view full answer...

Answer 7

I was able to get a dimension sheet from my contact at Curt for the Curt Hitch part #C15800 that you referenced. See attached pic. I also attached a set of the installation instructions for this hitch.

view full answer...

Answer 8

The Draw-Tite Ultra Frame Trailer Hitch Receiver w/ Cast Center #41946 is a confirmed fit for the 1996-2018 Chevy Express and GMC Savana Vans. There is not a confirmed fit for any E450 models, but I did measure the hitch as you requested to see if…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Measurements of Draw-Tite Trailer Hitch Receiver # 41920 for 1998 Ford Light Duty Pickup

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching