Availability of a Trailer Wiring Diagram for a 2012 Honda Goldwing and 1999 Escapade SE Trailer
Question:
need wiring diagram to wire 2012 goldwing to 1999 escapade se trailer
asked by: David W
Expert Reply:
Wiring your motorcycle to tow your motorcycle trailer will require some testing and investigation of the lighting configuration on your trailer.
First, check the lights on your 1999 Escapade SE trailer. If the trailer has separate lights or bulbs for the turn and stop lights then the trailer will have a 5 wire connector. In this case you will need to contact Honda for wiring for the trailer, that will protect the motorcycles circuitry. If the trailer has combined stop and turn signals then a standard circuit protected 4 wire trailer connector can be used, like # C59496.
Wiring diagrams for trailer wiring on the GoldWing are not available so you will need to use the circuit tester, included in the wiring kit, to verify the left turn, right turn, stop and tail light circuits on the motorcycle.
Once these wires are found you will connect the yellow wire from the converter to the left turn circuit , the green wire to the right turn circuit, the red wire to the stop light circuit and the brown wire to the tail light circuit. The black wire will then be ran from the converter to the positive terminal of the motorcycle battery through the inline fuse holder. The white ground wire should be connected to a good ground location.
Once all of the wiring connections are completed, install the fuse in the inline fuse holder and test the connector for proper function.
Finish up the install by finding a spot to mount the converter box with the double stick tape and route the 4-way connector to an accessible location at the rear of the motorcycle.
If Honda does not have a wiring harness for a 5 wire trailer you could look into replacing the lights on the trailer with lights that have combined stop an turn signals. If you would like to send me photos of the lights on your trailer, I would be glad to see if we have lights to replace those on your trailer.
Products Referenced in This Question
No-Drill Mount for Electrical Mounting Bracket - Short
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 4 Flat
- 5 Flat
- 4 Round
- 5 Round
- Tow Ready
more information >
Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- 8 Feet Long
- Universal Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
4-Way Flat Trailer Connector w/ 48" Harness and Wire Taps
- Trailer Wiring
- Trailer Connectors
- Vehicle End Connector
- 0 - 5 Feet Long
- Plug and Lead
- 4 Flat
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Comparing Demco Channel Tongue Trailer Couplers # DM16080-95 & # DM15931-95
- Article: Trailer Maintenance Schedule
- Q&A: Seal With Dimensions to Replace 171255UC
- Article: Trailer Wiring Diagrams
- Article: Trailer Tire Sizing
- Q&A: How to Determine if Trailer Axle is Not Aligned and How to Measure to Replace Trailer Axle
- Q&A: Solution for Replacement Seal for 171255UC Oil Seal
- Q&A: Can the Furrion Shark Fin Mounting Bracket Be Used With All of the Furrion Backup Cameras
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: How to Measure a Trailer Axle
- Q&A: Replacement Tire and Wheel for Trailex Sea Kayak Trailer 4.80-12 Galvanized Wheel
- Q&A: Inspecting Trailer Hub And Spindle For Signs Of Damage
- Article: How to Install E-Track in 3 Easy Steps
- Article: 2023 Best Gifts for RVers & Campers