What Parts Are Needed to Add Electric Brakes to a Trailer with a 2,000 Lb Axle
Question:
I have a trailer with a 2000lb ez lube axle made by Rockwell american with 12inch rims 5 on 4.5inch , I would like to install electric brakes on it. What other info is needed thanks,
asked by: Jerry
Expert Reply:
In order to install electric brakes on your trailer you will need a brake mounting flange, brake assembly, hub/drum, trailer wiring, breakaway kit, and brake controller. I have attached my recommendations on each of the following for you below:
Brake Mounting Flange: part # 4-34 (2)
Brake Assembly: part # AKEBRK-2
Hub/Drum: part # AKHD-545-2-EZ-2K (2)
Trailer Wiring: part # HS381-9000
Breakaway System part # 20099
Brake Controller: part # 90885
In order to be sure the above hub/drum is correct you would need to know the numbers on both the inner and outer bearings. If the numbers are not visible than you can always measure where they seat on the spindle with a digital caliper like part # PTW80157 to the thousandth of an inch. I have attached a help article to walk you through this process as well.
Products Referenced in This Question
Hopkins Engager Push-To-Test Trailer Breakaway Kit w/ Built-In Charger - Side Load - 7" Wire
- Trailer Breakaway Kit
- Kit with Charger
- Side Load
- Single-axle
- Tandem-axle
- LED Tester
- Hopkins
more information >
Brake Mounting Flange for 1-3/4" Round Trailer Axles - 2K
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- Electric Drum Brakes
- Hydraulic Drum Brakes
- Brake Mounting Flange
- 7 Inch
- 1-3/4 Inch Diameter Axle
- Redline
more information >
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
etrailer Electric Trailer Brakes - 7" - Left/Right Hand Assemblies - 2,000 lbs
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Manual Adjust
- 7 x 1-1/4 Inch Drum
- 2000 lbs Axle
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- etrailer
more information >
Easy Grease Trailer Hub and Drum Assembly for 2K Axles - 7" - 5 on 4-1/2 - L44649 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Easy Grease
- EZ Lube
- Pre-Greased
- L44649
- L44649
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- etrailer
more information >
Wiring Kit for Hydrastar Electric Over Hydraulic Actuators
- Accessories and Parts
- Brake Actuator
- Disc Brakes
- Hydraulic Drum Brakes
- Wiring
- Hydrastar
more information >
Product Page this Question was Asked From
4" Carbon Fiber Digital Caliper
- Hand Tools
- Measuring and Layout Tools
- Digital Calipers
- Carbon Fiber
- Performance Tool
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended Replacement Hubs For BT-150 Trailer Idler Hubs
- Article: Most Popular Wheel Bearings
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Q&A: How to Determine if Trailer has 84 Spindle to Pick Out Replacement
- Q&A: How to Confirm Correct Size of Grease Seal
- Article: Parts Needed to Add Hydraulic Disc Brakes to a Trailer
- Q&A: Comparing the E-Z Lube Hubs to the Standard Hub Assemblies for Trailer Axles
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: How to Bleed Your Trailer Surge Brakes
- Q&A: Trailer Wiring Harness Recommendation for 2017 Lexus RX 350 with Towing Package
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Q&A: 14 inch Diameter Rim and Tire Recommendation to Replace 175/80-13 on Trailer
- Article: How to Measure for Trailer Hitch Drop
- Article: Trailer Wiring Diagrams