Replacement Hitch Lock and Anti-Rattle for Thule T2 Classic 4 Bike Rack

Question

Question:

have thule classic t2 9044 and 9046 add on need replacement pin for hitch receiver... does STL2 fit? does not list classic T2 as rack . Thanks

asked by: Lorne

1

Helpful Expert Reply:

The Thule Snug Tite Hitch Lock and Anti-Rattle Device # THSTL2 is the correct fit for all Thule hitch mounted bile racks that use a pin.

expert reply by: Jason S

1

Answer 1

I went to our warehouse to pull this hex head bolt #908-1240-54. This bolt will have a property class of 8.8 and is classified as a high strength steel bolt. The point at which a bolt fails is the tensile strength, and because it is elongated (much…

view full answer...

Answer 2

The only replacement parts you need to secure your Thule Vertex 9029 to your hitch are #908-1240-54 for the M12 Bolt, #951-1224-54 for the Washer, and #956122159 for the Lock Washer. There is no replacement nut available, and no need for one. These…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Replacement Hitch Lock and Anti-Rattle for Thule T2 Classic 4 Bike Rack

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching