Recommended A-Frame Trailer Jack for 7,000 lb Flat Deck Car Trailer
Question:
Im looking for an A frame trailer jack with a 2inch outer tube diameter. Its hard to search on your site Prefer but not necessary Top wind Heaviest rating possible Application is flat deck car trailer. 7K gvwr Thanks
asked by: Vance A
Expert Reply:
The issue you are facing in finding what you desire is that the 2 inch outer diameter tube is standard for the inner tube of a trailer jack. That outer tube is consistently 2-1/4 inches in diameter. We do not currently have a top wind jack with that measurement.
We do however have a sidewind option in the Dutton-Lainson # DL22530 but it is only rated for 1,000 lbs. This is the only option we currently carry with that 2 inch outer diameter. You will need foot plate # DL22541 for this jack.
My recommendation for you is to use a rotary tool to enlarge the hole on your coupler to allow the standard trailer jack size of 2-1/4 inch outer diameter. The mounting bolt pattern will remain the 3 inch on center pattern. Then I recommend the Bulldog Round, A-Frame Jack - Topwind - 15" Lift - 5,000 lbs # BD155032 with footplate # BD018564.
Products Referenced in This Question
Replacement Square Footplate for Bulldog Round Trailer Jacks w/2" Diameter Tubes - 2" Tall
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Foot
- 2 Inch Diameter Tubing
- Bulldog
more information >
A-Frame Trailer Jack - Sidewind - 1,000 lbs. by Dutton-Lainson
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- Steel
- 0 - 1000 lbs
- Sidewind Jack
- 15 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- Dutton-Lainson
more information >
Removable Steel Foot with Pin for DL22530 A-Frame Trailer Jack by Dutton-Lainson
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Foot
- 1-3/4 Inch Diameter Tubing
- Dutton-Lainson
more information >
Product Page this Question was Asked From
Bulldog Round, A-Frame Jack - Topwind - 15" Lift - 5,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 4001 - 5000 lbs
- Topwind Jack
- 15 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- Bulldog
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Looking for Shorter A-Frame Jack to Clear my Tailgate
- Q&A: Recommended 5,000lb Topwind Trailer Jack Replacement
- Article: What are the Common Types of Propane Fittings Used on RVs?
- Q&A: Can't Lower Truck Tailgate Because it Hits the Trailer Jack
- Article: Trailer Wiring Diagrams
- Q&A: Placement and Number of Safety Chain Mounts Needed on Trailer
- Article: My Trailer Hitch Doesn't Fit
- Article: Best Hitch Cargo Carriers
- Q&A: Replacement Cover for Trailer Roof Vent AS-13 M-VD0449
- Article: Best Camper Jacks
- Q&A: Low Profile Trailer Jack Recommendation for Better Tailgate Clearance
- Q&A: Replacement Jack Options For a 2012 Casita Spirit Deluxe
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: Trailer Tire Sizing