Compatibility of Curt Ball Mount # C45310 with Curt Class III Hitch on 2005 Suzuki Grand Vitara
Question:
Hello, Can you please tell me if the items C45310 And A-90 will be fit my CURT 13517 Class 3 Trailer Hitch Thanks
asked by: Andreas
Helpful Expert Reply:
The Curt Ball Mount # C45310 referenced in your question is indeed compatible and will work nicely with your Curt Trailer Hitch Receiver # C13517. This particular Class III hitch is also confirmed to fit your 2005 Suzuki Grand Vitara. The 2 Inch Hitch Ball # A-90 that you also mentioned features a 1-1/4 inch diameter shank so it will work perfectly with the ball mount.
Since it sounds like you will be doing some towing, I recommend the Curt T-Connector Vehicle Wiring Harness # C55372 if you do not already have a trailer connector installed. This custom-fit harness will install by connecting directly to the built-in ports located behind the driver side trim panel. This will provide you with a 4-Way connector at the rear bumper of your Grand Vitara to connect with and power the trailer's basic signal lights.
I have attached the installation instructions for this harness that you can use for reference.
Products Referenced in This Question
2" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank - Chrome - 10,000
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-5/8 Inch Shank Length
- 1-1/4 Inch Diameter Shank
- 10000 lbs GTW
- Class IV
- Class V
- CURT
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Curt Ball Mount for 2" Hitches - 1" Rise, 2" Drop - 9-3/8" Long - 10,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1-1/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Measure for Trailer Hitch Drop
- Article: Trailer Maintenance Schedule
- Q&A: How to Bleed Electric Over Hydraulic Trailer Brakes
- Q&A: Correct Ball Mount for 19-3/4 Inch Receiver Height on 2021 Ford F150
- Q&A: Does the Pipe Mount BDPG9810-00 and Trailer Jack TJDP-7000S-B Have Same Pipe Dimensions
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: Troubleshooting Surge Brakes Locking Up When Moving Forward
- Article: Rust Prevention
- Q&A: Best Replacement for Atwood 82543 Brake Actuator
- Q&A: Can Electric Brakes be Used on a Boat Trailer
- Q&A: Replacement 12 x 2 Inch Electric Brake Assemblies for K-H KAE-96002-02
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Calculating Portable Generator Power Needs
- Article: Trailer Wiring Diagrams