Best Tonneau Cover Compatible with 5th Wheel Hitch on a 2017 Ram 3500

Question

Question:

I have a 2017 Ram 3500 DRW, 8foot bed, with a puck system in the bed. The 5th wheel hitch is a BandH Companion. Do you have an under the rail bed liner that will work with the hitch? Thanks,

asked by: Keith

0

Expert Reply:

You should not have any problem using a tonneau cover that mounts inside the bed rails on your 2017 Ram 3500 with B&W Companion 5th Wheel Hitch installed. As long as your 5th wheel hitch does not extend up past the bed rails on the truck then most of them will work for you.

I recommend the BAK Revolver X2 Hard Tonneau Cover part # BAK39214. This cover features several 1/4" thick rustproof aluminum slats which are extremely durable. The cover will lay flat after installed and will not wrinkle or crease like most others do. It can be locked against the cab while rolled up for towing applications. The cover is made here in the U.S.A and comes with a 3-year warranty.

I have attached a review video of the cover for you so you can see it in action.

expert reply by: Conner L

0

Answer 1

The Tonneau cover that is in the customer's pictures (see attached) is the BAKFlip F1 Hard Tonneau Cover #BAK72122. However in that same review, the customer says that the cover and the rack rub against each other. That rubbing will likely cause…

view full answer...

Answer 2

I attached a picture that shows the Bakflip G2 part #BAK26203 installed on a very similar 2017 Ram 3500 short bed and you can see that with the last panel folded down the fifth wheel hitch head is accessible. This means you'd also have access to…

view full answer...

Answer 3

Both of the hitches you asked about have some great features. They both have dual jaws for better king-pin contact, and both have the same towing and vertical load limit capacity. There are a few differences between the hitches. The hitch height of…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Best Tonneau Cover Compatible with 5th Wheel Hitch on a 2017 Ram 3500

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching