Recommended 2 Inch Hitch Stabilizer and Cover for Curt Class III Trailer Hitch
Question:
I have a Curt Trailer Hitch Receiver - Custom Fit - Class III - 2inch Item # C13152 that I installed. I recently purchased the Draw-Tite QSP Trailer Hitch Silencer and Cover for 2inch Hitch Receivers Item # 63080. I am trying to install the silencer as directed and it will not fit over the lip of the hitch no matter how hard I try pushing it on. I dont want to risk using a hammer to tap it on unless you recommend it. Any advise would be greatly appreciated.
asked by: Robert M
Expert Reply:
I do have a solution for you, however the collar on the receiver portion of the Curt Trailer Hitch Receiver # C13152 that you mentioned is simply too large to accommodate fitment of the Draw-Tite QSP Trailer Hitch Silencer # 63080. I went out to the warehouse to test fitment and found the same issue that you did. Because this cover is specially designed for Draw-Tite hitches, there are certain Curt hitches that it will not work with.
For a similar anti-rattle/stabilizing device, I recommend looking at the Brophy Stabilizer Bracket # RHSB. This will actually slide over the shank of your accessory (bike rack, ball mount, etc), and not the hitch receiver itself. Once mounted, you will simply tighten the screws onto the lip of the hitch to secure it into place and reduce any movement of the accessory. I have attached a short video demonstration on this product so you can see exactly how it works.
Then for a 2 inch hitch cover, you can use the Curt part # C22272.
Products Referenced in This Question
Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers
- Hitch Anti-Rattle
- Standard Anti-Rattle
- Manufacturer Specific
- Fits 2 Inch Hitch
- Sleeve Style
- Accessory Anti-Rattle
- Draw-Tite
more information >
Brophy Stabilizer Bracket for 2" Hitch Receiver - Black Powder Coated Steel
- Hitch Anti-Rattle
- Standard Anti-Rattle
- Universal
- Fits 2 Inch Hitch
- Sleeve Style
- Accessory Anti-Rattle
- Brophy
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 900 lbs TW
- 6000 lbs GTW
- 8000 lbs WD GTW
- 2 Inch Hitch
- 900 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended Hitch for a 2014 Hyundai Santa Fe Sport
- Q&A: Roof Rack and Cargo Basket Recommendation for 2015 Honda CR-V with Naked Roof
- Q&A: Brake Controller for 2019 Ford Edge With Factory Tow Package
- Q&A: Dexter Hub Replacement for Hub Part # K08-219-9B
- Q&A: Aero Bar Roof Rack that Fits 2022 Toyota Highlander
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: How to Determine if 2015 Kia Sorento EX Has Factory Tow Prep Package
- Q&A: Comparing 2" Trailer Hitch Receivers For 2017 Hyundai Santa Fe Sport 2.0 Turbo
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: How to Choose a Hitch-Mounted Bike Rack
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size