Adding Electric Over Hydraulic Drum Brakes to a Trailer
Question:
Thanks for your response, My tow vehicle is a 2011 Chevy 3500hd 4wd ,dual wheels.It has a factory brake actuator and 7 flat plug. I don't know if the P2 unit would plug into those wires or not?
asked by: Duff P
Expert Reply:
With 6,000 pound axles they must take 12 x 2 inch assemblies. For a left and right side pair of assemblies you can use # AKFBBRK-7. We do not have an option for self-adjusting brakes in this size with a single-servo design.
For an actuator I recommend the Hydrastar # HS381-9066. This unit is rated to 1,200 psi so it provides a little extra kick above the 1,000 psi units. Since you have a couple of 6,000 pound axles you're going to want the best to slow the loaded trailer down. It also includes the breakaway system and wiring to add a 7-Way connector to the trailer. If the trailer already has a 7-Way and breakaway system then use # HS381-8066 for just the actuator.
Your tow vehicle will also need to have a brake controller that is compatible with electric over hydraulic brakes. There are not all that many that are compatible so you can't use just any controller. I recommend the P2 # 90885 because it is easy to set up and use and it is reliable.
If you can tell me the year, make, and model of the tow vehicle I can make some additional recommendations for adding a 7-Way connector to the tow vehicle. I have also included a link to our help article that explains everything needed to add electric over hydraulic drum brakes to a trailer.
Products Referenced in This Question
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Hydrastar Electric Over Hydraulic Actuator Adapter Module for Ford and Chevy Brake Controllers
- Accessories and Parts
- Brake Actuator
- Disc Brakes
- Hydraulic Drum Brakes
- Adapters
- Hydrastar
more information >
Hydrastar Vented Marine Electric Over Hydraulic Actuator for Drum Brakes - 1,200 psi
- Brake Actuator
- Electric-Hydraulic Brake Actuator
- 1200 psi
- Drum Brakes
- Hydrastar
more information >
Hydrastar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness - 1,200 psi
- Brake Actuator
- Electric-Hydraulic Brake Actuator
- 1200 psi
- Drum Brakes
- Hydrastar
more information >
Product Page this Question was Asked From
Hydraulic Brake Kit - Uni-Servo - Free Backing - 12" - Left/Right Hand Assemblies - 5.5K to 7K
- Trailer Brakes
- Hydraulic Drum Brakes
- Standard Grade
- Free Backing
- Manual Adjust
- Single Servo
- 12 x 2 Inch Drum
- 5200 lbs Axle
- 6000 lbs Axle
- 7000 lbs Axle
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Replacement Hub and Drum Assembly for 2006 Karavan Trailer
- Article: How to Bleed Your Trailer Surge Brakes
- Q&A: Could Demco Actuator part # DM72VR be Manually Locked Out with Rod
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Q&A: Replacement for Atwood Surge Brake Actuator 85778
- Q&A: Difference Between Single, Dual and Free Backing Servo Brake Assemblies
- Q&A: Replacement Coupler for 2007 Mastercraft X15 Boat Trailer
- Q&A: Recommended Replacement Brake Actuating Surge Coupler for Atwood 85778
- Q&A: Master Cylinder Brake Line Fitting for Titan Model 60 Disc Brake Actuator
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Trailer Wiring Diagrams
- Article: Testing Breakaway Systems
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: Hand Winches
Duff
2/5/2018
Thanks for your response, My tow vehicle is a 2011 Chevy 3500hd 4wd ,dual wheels.It has a factory brake actuator and 7 flat plug. I don't know if the P2 unit would plug into those wires or not?