Necessary Modifications to Install Draw-Tite Class III Receiver on 2008 Ford Edge
Question:
does the bumper on my 2008 ford edge sel awd have to be trimmed,modified,or changed to a factory bumper for a hitch
asked by: Jackilyn
Expert Reply:
The Draw-Tite Class III Receiver you referenced, part # 75992 does not require any trimming or other modification of the bumper fascia. However, there are two heat shields that are attached to the frame members under the vehicle that will need a bit of trimming. If you look at figure # 2 on the install instructions that I have linked to, you will see a diagram showing the small portions that will need to be trimmed away.
This hitch fits all Edge models except for the Sport model.
To complete your towing setup, you might also need the following items:
Trailer Wiring Harness part # 118551
Draw Bar part # AMSC2
1-7/8 inch hitch ball part # 19260
2 inch hitch ball part # 19247
Pin and clip part # PC3
Locking Hitch Pin # e98882
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Matte Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- Shock Absorbing
- Convert-A-Ball
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitch - Flush - 2-5/8" Span - Stainless Steel
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Stainless Steel
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Wheel To Replace Discontinued Lionshead Black Tiger Wheel for Camper
- Q&A: I A Latch For My RV Door That Has A 4-1/2 inch X 4-1/2 inch Hole
- Q&A: Recommended Replacement Grease Seal for 2014 Shorelander Boat Trailer
- Q&A: Trailer Hitch Receiver and 4-Way Flat Vehicle Wiring Harness For a 2024 Ford Maverick
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Why Is a 10" Lube Plate Recommended for a B&W Companion Instead of 12"
- Article: My Trailer Hitch Doesn't Fit
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Q&A: Recommended Trailer Hitch Receiver to Tow a Trailer with a 2012 Ford Edge
- Article: Best Bike Racks for Fat Bikes
- Article: How to Choose a Bike Rack for an SUV or Crossover