Parts Needed to Flat Tow 2008 Jeep Wrangler
Question:
I own a 2016 40 QBH Phaeton by Tiffin and tow a 2 door 2008 Jeep Wrangler with auto transmission. What system would you suggest for me to install Thanks
asked by: Phillip C
Expert Reply:
You would want to start with the Roadmaster Base Plate kit part # RM-521448-4 for flat towing your 2008 Jeep Wrangler.
In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle. The most popular compatible tow bar is the Falcon 2, # RM-520. For safety cables you can use # RM-643. The coiled design helps keep the cables off of the ground.
For lighting you can use the diode kit, # RM-15267, and not have to worry about cutting into the taillight housing. This will splice into your taillight wiring to allow your tow vehicle to control the taillight assemblies of the towed vehicle. This comes with a round 6-way connector that you will install on the front of your towed vehicle and enough coiled wire to go from there to the RV.
And finally, most states now require supplemental braking in the vehicle being flat towed. The easiest system to set up and use is the Blue Ox Patriot # BLU37TR, that applies the vehicle brakes in proportion to how much the tow vehicle is braking. This is the safest way to stop and it reduces wear and tear on both vehicles.
Most likely you will also need a high low adapter so that the tow bar will be level when you are flat towing. I attached a link to a page that has all of the ones we carry.
I have included a couple of helpful links to our articles on flat towing for you. Be sure to consult the vehicle owners manual for more specific information on flat towing your vehicle.
Products Referenced in This Question
Blue Ox Patriot Portable Flat Tow Brake System - Proportional
- Tow Bar Braking Systems
- Brake Systems
- Proportional System
- Recurring Set-Up
- Portable System
- Power Assist Brake Compatible
- Air Brakes
- Air Over Hydraulic Brakes
- Hydraulic Brakes
- Blue Ox
more information >
Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Tow Bar Wiring
- Splices into Vehicle Wiring
- Diode Kit
- Universal
- Tail Light Mount
- Roadmaster
more information >
Roadmaster Falcon 2 Tow Bar - RV Mount - 2" Hitch - 6,000 lbs
- Tow Bar
- Hitch Mount Style
- Telescoping
- Steel
- 6000 lbs
- Fits Roadmaster Base Plates - Crossbar
- Fits Roadmaster Base Plates - Direct Connect
- Stores on RV
- Standard
- Roadmaster
more information >
RoadMaster 68" Single Hook, Coiled Safety Cables - 6,000 lbs
- Safety Cables
- Coiled Cables
- 68 Inch Long
- 6000 lbs GTW
- Snap Hooks
- Coated Cables
- Roadmaster
more information >
Product Page this Question was Asked From
Roadmaster Crossbar-Style Base Plate Kit - Removable Arms
- Base Plates
- Removable Drawbars
- Twist Lock Attachment
- Roadmaster
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Article: Trailer Wiring Diagrams
- Article: Roadmaster Vehicle Specific Base Plates
- Q&A: How to Determine if Trailer Axle is Not Aligned and How to Measure to Replace Trailer Axle
- Q&A: Best Replacement for Old 6.00-16 Trailer Tires
- Q&A: Replacement Amber Lens for Trailer Light with SAE A P2 DOT 14
- Article: Flat Towing Package for 2007-2018 JK Jeep Wrangler and Wrangler Unlimited
- Article: Guide to Choosing the Best Truck for 5th-Wheel Towing
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Must-Have Flat Towing Components
- Q&A: Comparing the Curt Q20 and the Curt A20 5th Wheel Hitches.
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
- Q&A: Recommended Base Plate for 2024 Ford Maverick With a Blue Ox Base Plate That's Too Wide
- Q&A: What do I Need to Flat Tow a Jeep Wrangler JK with Factory Bumper