Recommended Trailer Hitch Ball Mount for a 2014 Toyota Sienna Using Curt Hitch # 13105
Question:
Im wondering what you recommend for the hitch ball mount for a Toyota Sienna 2014 to be used with a Curt trailer hitch part number c 13105
asked by: Adam
Expert Reply:
Since the Curt trailer hitch receiver, part # C13105, sits pretty low on your 2014 Toyota Sienna you probably are going to need a ball mount with a rise. Something like the Draw-Tite, part # 2753, which has a 2-3/4 inch rise. Or you can get the kit that includes both 1-7/8 and 2 inch hitch balls, a pin and clip, and storage bag, part # EBMK4.
The best way to determine exatly how much rise you need out of a ball mount is to measure from the ground to the inside top of the receiver tube on the hitch. When we installed the hitch we measured it at 10-1/2 inches. Then measure from the ground to the underside of your trailer's coupler. Then find the difference. I've linked an article that explains this in more detail.
Also, if you need a wiring harness for your van I recommend part # 118498 which plugs in behind both tail lights. Then you need to run a power wire up to the van's battery.
I've linked some install videos of the hitch and wiring for you as well.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Draw-Tite
more information >
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 6000 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Comparing Curt and etrailer Hitch for 2023 Toyota Sienna
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Dimensions of C-Channel for Enclosed Trailer # 362213-955
- Q&A: Differences Between Curt, Draw-Tite, and etrailer.com Trailer Hitches for 2019 Subaru Outback Wagon
- Q&A: Recommended Trailer Hitch Receiver For 2013 Toyota Sienna SE
- Q&A: Tongue Weight Rating of 2016 Toyota Sienna When Using the Draw-Tite Max-Frame # 76112 Trailer Hitch
- Article: How to Measure for Trailer Hitch Drop
- Article: My Trailer Hitch Doesn't Fit
- Article: Rust Prevention
- Article: Best Bike Racks for Electric Bikes
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch