Factory Pressure Setting for Invisi-Brake System # RM-8700

Question

Question:

What is the factory setting for the brakes? I think that the dial was moved before I installed the unit.

asked by: Jim C

0

Expert Reply:

The braking pressure that the Invisi-Brake System # RM-8700 that you referenced comes from the factory set at is the most universal setting that works for most applications, 60 psi.

You will want to test your setup using the preset setting and compare the stopping power to how the RV stops without a vehicle behind it and adjust as necessary.

expert reply by: Jameson C

0

Answer 1

On the Roadmaster InvisiBrake Supplemental Braking System #RM-8700 you will adjust the braking pressure between the 5 psi minimum and the 80 psi maximum based on the behavior of your specific Wrangler XL as well as personal preference. The factory…

view full answer...

Answer 2

When installing the Roadmaster InvisiBrake Supplemental Braking System, #RM-8700 it is advisable to go to the roadmaster web site (listed in your installation instructions and linked below) and select the "Vehicle Specific Info" tab…

view full answer...

Answer 3

The braking pressure that the Invisi-Brake System #RM-8700 that you referenced comes from the factory set at is the most universal setting that works for most applications, 60 psi. You will want to test your setup using the preset setting and compare…

view full answer...

Answer 4

Yes the Roadmaster InvisiBrake Supplemental Braking System Item #RM-8700 will connect directly to your towed vehicle's battery and charge it while driving unlike most braking systems that would actually drain your battery. Some notes to consider…

view full answer...

Answer 5

Roadmaster gives an estimate of 3 hours for their Base Plate #RM-523193-5 on your 2020 Chevrolet Equinox LS. Do understand that this time from is for an experienced technician. If you are installing this yourself Bill, I would double that time for an…

view full answer...

Answer 6

First of all you're correct, that isn't the normal way to connect a tow vehicle to a motorhome and I don't recommend it since that isn't how the tow bar or base plates are designed to be used. Instead you should connect them and then…

view full answer...

Answer 7

The Invisibrake part #RM-8700 does draw power form your Forester battery to activate so over time the battery will eventually drain if not maintained while flat towing. So what you can do is install the Roadmaster Battery Charge Line Kit #RM-156-25…

view full answer...

Answer 8

The air pressure in the Roadmaster InvisiBrake Supplemental Braking System #RM-8700 will slowly release the pressure until it is down to zero when you disconnect your 2017 Ford Focus from your motorhome. It won't drop all of the sudden once…

view full answer...

Answer 9

It sure does. When the RV running lights are turned on, the InvisiBrake will deliver a trickle charge to the battery of the towed vehicle. I've linked you to the installation instructions for the Roadmaster InvisiBrake. If you go to the product…

view full answer...

Answer 10

The braking pressure that the Invisi-Brake System #RM-8700 that you referenced comes from the factory set at is the most universal setting that works for most applications, 60 psi. You will want to test your setup using the preset setting and compare…

view full answer...

Answer 11

If the exhaust brake makes the brake lights/tow package trailer connector on the RV come on then it will trigger the InvisiBrake #RM-8700. There is a solution but there isn't an easy way to bypass the exhaust brake from setting off the…

view full answer...

Answer 12

The braking pressure that the Invisi-Brake System #RM-8700 that you referenced comes from the factory set at is the most universal setting that works for most applications. You will want to test your setup using the preset setting and compare the…

view full answer...

Factory Pressure Setting for Invisi-Brake System # RM-8700

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching