Sway Control Bracket on Both Sides of a Ball Mount

Question

Question:

Do you hahe this item for either side.

asked by: Bernard

0

Expert Reply:

I am sorry, but the Curt Ball Mount with Sway Control Bracket, part # D320, is only offered with the sway control bracket on the right side. We do offer a Sway Control Tab, part # 3442, that you can weld onto a ball mount. Or, we also offer a Sway Control Adapter, Left Side, part # 3475, that can be used with a Round Bar weight distribution head.

expert reply by: Andi

0

Answer 1

The handle is actually the on/off switch for the unit and the bolt under the handle is the tension adjustment bolt. You will need to turn the On/Off handle clockwise (tighter) until the handle will stay firmly in place parallel with the main body…

view full answer...

Answer 2

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball…

view full answer...

Answer 3

We don't have a wider bracket than the #RP26005 for your ball mount so the best option we would have would be a new ball mount that has the bracket already attached like the Curt #D320 which has a drop of 2 inches since you aren't…

view full answer...

Answer 4

The #3442 replacement sway control tab would be welded onto the side of a ball mount, and the 1-1/4 inch diameter trailer ball would mount in the 5/8 inch diameter hole in the tab. If a ball mount with a 3/4 inch rise or a 2 inch drop would work,…

view full answer...

Answer 5

Yes, the Jensen Mechless RV Stereo #JWM20 has a plug in for an antenna on the back. I have included a diagram from the installation instructions that shows this, as well as a picture of the back of the stereo where you can see the plug in.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Sway Control Bracket on Both Sides of a Ball Mount

Product Page this Question was Asked From

Continue Researching