Curt Trailer Hitch # 13053 Bolt Hole Dimensions
Question:
How widt is from side by side between holes close to the bumper Thanks
asked by: Adrian
Expert Reply:
This hitch measures 38 inches from bolt hole center to bolt hole center on all of the holes except for the rear most set of holes. These are 39-1/2 inches in width.
Check out the picture I attached to see this measurement.
You may be interested in the following products to complete your towing setup:
Tow Ready Custom Fit Vehicle Wiring # 118344 (instructions attached)
Ball Mount 1 inch Rise or 2 inch Drop # C45030
Hitch Ball with 2 inch Diameter and Medium Shank # 19247
Hitch Ball with 1-7/8 inch Diameter and Medium Shank # 19260
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 1" Rise, 2-1/4" Drop - 7-5/8" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 7500 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: What Roof Boxes Will Fit On The Rhino Rack HD Square Crossbars
- Q&A: Dimensions Between Side Plates of the Curt Trailer Hitch Receiver # 13053
- Q&A: Master Cylinder Brake Line Fitting for Titan Model 60 Disc Brake Actuator
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Can a 5.30-12 Size Tire be Replaced with a ST145/R12 Size Tire
- Article: Stability Control for Heavy Duty Vehicles
- Article: Best Air Bag Suspension (2023)
- Q&A: Hitch Needed for 2004 Ford Cut-Away Van Chassis
- Article: Performance Chips and Modules
- Q&A: Replacement Switch for Lippert Electric Stabilizer Jacks
- Q&A: Replacement Switch for Lippert LCI #198641 Stabilizing Jack
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Brake Controller Installation on a Ford Full-Size Van