Recommended Trailer A-Frame Coupler and Jack for Coleman Royale Destiny Pop-Up Camper
Question:
My son has a Coleman royal destiny pop up camper. He needs the trailer ball coupler and the, I am not sure what this is called but its the part you wind up to remove the trailer and down to put the trailer on the hitch. Can you help me out?
asked by: Brian A
Helpful Expert Reply:
For your son's Coleman Royale Destiny Pop-up, I recommend the Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Black - 2" Ball - Bolt On - 10K # DM14793-81 because it is an easy bolt on installation for 2 inch hitch ball compatibility. A more economical option is the weld on A-Frame Trailer Coupler - Yoke Latch - Black - 2" Ball - Weld On - 8,000 lbs # CA-5210-B.
Both have the trailer jack attachment point for easy mounting of your jack to raise and lower the trailer tongue. For this jack, I recommend the Pro Series Round, A-Frame Jack - Topwind - 15" Lift - 2,000 lbs # PS1401000303. Then you will want to use either the foot # PS1400700340 or the wheel # PS1400750340.
Products Referenced in This Question
A-Frame Trailer Coupler - Yoke Latch - Black - 2" Ball - Weld On - 8,000 lbs
- A-Frame Trailer Coupler
- Standard Coupler
- Weld-On
- 8000 lbs GTW
- 2 Inch Ball Coupler
- Yoke Latch
- etrailer
more information >
Pro Series Detachable Footplate w/ Pin for 2" Diameter Jacks - 2,000 lbs to 5,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Foot
- 2 Inch Diameter Tubing
- Pro Series
more information >
Pro Series 6", Detachable Caster w/ Pin for 2" Diameter Jacks - 1,200 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Wheel
- 6 Inch Wheel
- Wheel w Caster Assembly
- 2 Inch Diameter Tubing
- Pro Series
more information >
Pro Series Round, A-Frame Jack - Topwind - 15" Lift - 2,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Topwind Jack
- 15 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- Pro Series
more information >
Product Page this Question was Asked From
Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Black - 2" Ball - Bolt On - 10K
- A-Frame Trailer Coupler
- Standard Coupler
- Bolt-On
- 10000 lbs GTW
- 2 Inch Ball Coupler
- Auto Latch
- Demco
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Troubleshooting A Clunking Noise Between A Fifth Wheel Hitch And Base Rails While Towing
- Q&A: Scissor Jack Recommendation to Replaced Damaged Ones on R Pod Trailer
- Article: Best Ladder Racks
- Q&A: Replacement Parts for Fan-Tastic Vent 8000 Series
- Q&A: Installation of Hitch on Fifth Wheel Trailer
- Q&A: When Flat Towing a Vehicle How Much Tongue Weight is on the Trailer Hitch
- Q&A: Can You Replace A GE Air Conditioner Be Replaced With An Advent A/C?
- Q&A: How to Measure the Angle of Trailer A Frame To Determine if a 50 Degree A Frame Coupler will Fit
- Article: Trailer Wiring Diagrams
- Article: How to Choose a Trailer Hitch Coupler
- Article: Trailer Lighting Requirements
- Article: Most Popular Wheel Bearings
- Article: My Trailer Hitch Doesn't Fit
- Article: Overview of Lubricating Grease