What Size Hole is Needed for Epicord 30 Amp Twist Lock Power Inlet

Question

Question:

What size hole is needed for this?

asked by: Juan

0

Expert Reply:

The Epicord 30 Amp Twist Lock Power Inlet # 277-000137 referenced in your question will require you to cut out a 3 inch diameter hole. The power inlet is then recessed into the wall by a length of 2-1/4 inches. The mounting holes are spaced apart 2-7/16 inches, center to center.

I have attached a short video demonstration on this product that you can also check out.

expert reply by: Chris R

0

click to enlarge

Answer 1

The Green/Black wire is the subwoofer negative and the solid green is the subwoofer positive on the iRV RV Stereo - Single DIN - AUX/USB, Bluetooth, App Control - 50W - 3 Zone - 12V Item #292-101809.

view full answer...

Answer 2

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 3

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 6

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…

view full answer...

Answer 7

The best way to determine the weight capacity of your leaf springs would be to check the weight rating of the axle on your trailer. The trailer will have a plate or sticker on it that will list the VIN number. The weight rating of the axle should be…

view full answer...

Answer 8

So I have your hub narrowed down to a few different possibilities but we need to know what your bolt pattern is to know for sure. We have the part #84556UC3 for if your bolt pattern is 5 on 5 inch. We have the part #845476UC3 for if your bolt pattern…

view full answer...

Answer 9

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

Slipper Springs like #e33SR do not use a bolt and bushing for the open eye end of the spring. It connects directly to the hanger using a slipper spring hanger kit.

view full answer...

What Size Hole is Needed for Epicord 30 Amp Twist Lock Power Inlet

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching