Availability of Load Stops to Fit Factory Roof Rack Crossbars

Question

Question:

I am looking for load stops to fit a ford oem roof rack that is currently on my Ford Explorer. Can you tell me what is compatible?

asked by: Conrad H

0

Expert Reply:

Does your Ford Explorer have a factory roof rack that has T-channels on top of the bars that are 3/4 inch wide? If so we have a solution.

Most roof rack T-slots are right at 3/4 of an inch wide at the base of them. If the slots on your crossbars are right at 3/4 of an inch wide at the base you could use the part # 753-3761 to fit in them.

expert reply by: Jameson C

0

Answer 1

The Yakima HD Crossbars won't work with Rhino-Rack Mounting Legs part #RRRLT600 but they do offer the very similar Rhino-Rack Heavy-Duty Roof Rack Crossbars part #RB1650B-2 which will work if used with the Roof Rack Leg Spacer Blocks part…

view full answer...

Answer 2

Most roof rack T-slots are right at 3/4 of an inch wide at the base of them. If the slots on your crossbars are right at 3/4 of an inch wide at the base you could use the part #753-3761 to fit in them.

view full answer...

Answer 3

Yes, the Load Stops for Rhino-Rack Aero/Sportz Crossbars #S602 will fit your Malone AirFlow2 Roof Rack #MPG216. These load stops measures 4" tall, and is made from durable glass-reinforced nylon. Attached is a review video for you to check…

view full answer...

Answer 4

The Load Stops for Rhino-Rack Heavy-Duty Crossbars #RRRLH1 are intended for a larger channel than what the Malone AirFlow2 part #MPG215 you mentioned has. For a different set that would work well you'd want the Rhino Rack Vortex Crossbar…

view full answer...

Answer 5

You are going to have to measure the size of the t-slots to know if we have load stops that would fit. The Thule Load Stops T-bolts #753-3761 are 3/4 inches square (0.75). If you measure the T-slots of your rack and these would fit this would be a…

view full answer...

Answer 6

Yes, the Malone AirFlow2 Roof Rack part #MPG216 will allow you to carry plywood on the roof of your 2016 Jeep Patriot. I recommend placing the crossbars as far apart as possible in order to evenly distribute the weight. There will be no damage to…

view full answer...

Answer 7

I spoke with my contact at Thule and the first thing she said is that the Load Stops part #753-3761 that you referenced have only been tested to fit the Thule Aeroblade cross bars. However, the T-bolts of the #753-3761 are .75 inches square. You…

view full answer...

Answer 8

You can use the Rhino Rack Load Stops #RRRLH2, which fit the Malone AirFlow2 crossbars on the Malone AirFlow Roof Rack #MPG216. I'd use these paired with some straps like the etrailer Cam Buckle Cinch Straps w/ Buckle Protectors - 1" x…

view full answer...

Answer 9

What I recommend is to add some load stops to the roof rack crossbars so that you can support the load side to side and use straps to secure the lumber front to back and tie off to the load stops. First you will need a roof rack for your 2014 Nissan…

view full answer...

Answer 10

The Load Stops for Rhino-Rack Vortex Aero Crossbars #RRRLH2 install by sliding into the T-Slot of the crossbar. For the 53" Thule WingBar Evo Crossbars #TH711420 the load stops will slide between the dual rubber T-Slot strips so you won't…

view full answer...

Answer 11

Here is a list of the load stops we carry for different roof rack systems. Some of them can be used on other roof racks systems I just need to know which one you have to verify which ones will fit. Load Stops for Thule Aeroblade Load Bars, Ladder…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Availability of Load Stops to Fit Factory Roof Rack Crossbars

Product Page this Question was Asked From

Continue Researching