What Clamps are Needed to Install the TracRac SR # TH43002XT-781 on a 2015 Chevy Silverado 2500 HD

Question

Question:

2015 2500hd silverado tracrac base rails install Tracrac sr base rails what clamps are needed for the rear pockets?

asked by: Happy

0

Expert Reply:

The clamps needed to install the TracRac SR Sliding Truck Bed Ladder Rack # TH43002XT-781 in the rear pockets of your 2015 Chevrolet Silverado 2500 HD 6-1/2 foot bed are included with the hardware. I have attached a photo pointing out the clamps from our photo of all the hardware for you to reference.

expert reply by: Jon G

0

click to enlarge

Answer 1

The only tonneau cover we have confirmed to work with the TracRac SR Sliding Truck Bed Ladder Rack part #TH43002XT-781 or part #TH43002XT-781EX for your 2017 Chevy Silverado 3500 is the BAK Revolver X2 Hard Tonneau Cover part #BAK39121. The BAK…

view full answer...

Answer 2

The Thule TracRac SR Sliding Truck Bed Ladder Rack item #TH43002XT-781 attaches to the top of your Silverado's bed by installing directly into the stake pockets. There is an included adapter nut that will have to be used to install the rear…

view full answer...

Answer 3

Thank you for all the details on your desired setup. In my opinion nothing compares to the combination of the TracRac SR adjustable ladder rack and BAK Revolver hard tonneau cover. Both of these are outstanding products and they are fully compatible…

view full answer...

Answer 4

I have a similar solution, but the Thule Rod Vault does not have a T-bolt adapter to allow it to fit the top channels of your TracRac ladder rack so instead you'd want to go with the Yakima TopWater Rooftop Fishing Rod Carrier - Locking - 8…

view full answer...

Answer 5

The Yakima Outdoorsman 300 Ladder Rack #Y01137-Y00410 is a great fit for your GMC Sierra 2500 that does not have bed guards. It wouldn't be too harsh in any way and also would not come undone after long travel either as it installs very…

view full answer...

Answer 6

Yes, TS Rails like the #TH75FR are compatible with both the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack for Tonneau Cover - 60" Crossbars #Y01151-5755 and a BAK Revolver X4S cover like the #BAK24ZR. If you could provide me with the…

view full answer...

Answer 7

The Rack'Em Rack for Truck Bed Side Rails has been discontinued, but wouldn't be a good option for what you are trying to accomplish anyway. To carry items like kayaks and a roof top tent you will need a stronger foundation such as a ladder…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

The Reese Titan Extension/Reducer you referenced, part #RP45292 would work great with the 2-1/2 inch Class V hitch on your Ram. As you mentioned, the extension has a 8K capacity when cut down to the 24 inch length, that will provide a 2 inch receiver…

view full answer...

Answer 11

There is a Titan hitch extender that should work for you, but would require a Titan hitch be installed on your truck to handle a tongue weight loaded that far from the hitch. It is Reese part #RP45292. You can use it as a 34 inch extension or cut it…

view full answer...

Answer 12

You can use a 7-Way and 4-Way connector at the same time just as long as you are not overloading the light circuits. If your camper has a lot of outside lights like running lights, and brake/stop/turn lights then the lights that perform the same…

view full answer...