Longer Shank Recommendation for E2 Weight Distribution System

Question

Question:

Need a longer hitch shank for my e-2 8000 lb wd hitch. Is the 14 inch reese shank compatible? Want to be able to open my truck tailgate . Have to be perfectly straight with trailer 2018 micro minnie just clears by a whisker

asked by: Richard W

0

Expert Reply:

For a longer weight distribution shank that would be compatible we have the Curt part # C17122 which measures 16 inches in length.

expert reply by: Jameson C

0

Answer 1

Yes, you can use the Equal-i-zer Weight Dist Shank #EQ90-02-4600 with your Fastway e2 WDS. Weight distribution shanks are pretty universal so you'll have no issues using this one.

view full answer...

Answer 2

The Equal-i-zer Weight Dist Shank part #EQ90-02-4600 should allow you to tow with the tailgate down on your 2017 Ram 3500. I have attached a photo for you of this shank used with a similar system on a similar truck

view full answer...

Answer 3

For your 1,150 pound ATV with 10" wide tires, I recommend the Erickson Arched Loading Ramps - Center Fold - Aluminum #EM07441-2. These ramps have an overall weight capacity of 1,500 pounds and measure 90" long x 12" wide. With these…

view full answer...

Answer 4

The Stallion Arched Loading Ramp Set - Center Fold - Aluminum - 88-9/16" Long x 13" Wide - 1.5K #288-07452-2 will work well to get your golf cart into the bed of your Ram 2500 4x4. The maximum loading height for these ramps is 35 inches.…

view full answer...

Answer 5

We have found a few brands that use their own unique weight distribution shanks, but for the most part they are universal, including your Eaz-Lift shank. You can verify this by measuring the diameter of the bolt holes (3/4 inch diameter) and the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Longer Shank Recommendation for E2 Weight Distribution System

Product Page this Question was Asked From

Continue Researching