Parts Needed to Install 7-Way and Brake Controller on 2016 Jeep Wrangler Unlimited
Question:
What about charging the batteries on the trailer?
asked by: Lisa
Expert Reply:
With the part # HM4190 you'd be able to wire a brake controller to it, but you would not have a quick connect port under the dash of your 2016 Jeep Wrangler for installing the controller.
For a wiring kit to install the brake controller to the 7-way you would want the Wiring Kit for 2 and 4 Brake Electric Brake Controllers # 5506. This will provide the power source and ground for the wiring for the brake controller. You will need to test the wires from the brake pedal switch of your vehicle to find a circuit that has voltage when the brakes are applied and none when not applied. This will be the circuit you will run the red wire to.
Finally you will need to run a length of 10 gauge wire (part # 10-1-1) from the brake output circuit of the controller to the brake output circuit of the 7-way (blue wire). The # 10-1-1 is sold by the foot so you will need to order a quantity of the amount of feet you will need.
For a brake controller I would recommend the Prodigy P3 Brake Controller part # 90195. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes. This will be the last brake controller you buy. It can easily be transferred to future vehicles as well.
![Jameson C](https://images.etrailer.com/static/images/catg/people/371_tn.jpg)
Products Referenced in This Question
Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
40 Amp In-Line Circuit Breaker - Perpendicular Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 40 Amp
- Pollak
more information >
Product Page this Question was Asked From
Hopkins Endurance Quick-Install 7-Way Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 7 Round - Blade
- Hopkins
more information >
Featured Help Information
Instructions
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Flat Towing Package for 2007-2018 JK Jeep Wrangler and Wrangler Unlimited
- Article: Which Sway Control Hitch is Right For Your Trailer?
- Q&A: How to Install a Brake Controller on a 2015 Jeep Wrangler Unlimited with Factory Tow Package
- Article: Brake Controller Installation: Starting from Scratch
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: Why It Is Better to Replace Entire Trailer Brake Assembly When Pads Are Worn Out
- Q&A: Is the etrailer # e67ZR Tow Bar the Same As the Demco Excali-Bar III?
- Q&A: Recommended Parts for Flat Towing a 2022 Jeep Wagoneer
- Q&A: What is the Flashing Pattern of the Prostrobe White Side Marker Light PRS70753
- Q&A: What Size Hole Normally Gets Drilled to Install 7-Way
- Q&A: Can I Add A Wire Harness To My Camper To Make It Tow Another Utility Trailer
Lisa
10/26/2017
What about charging the batteries on the trailer?