How Low does the Curt Hitch C13065 Hang on the 2011 Grand Cherokee
Question:
I noticed Jeeps stock hitch is a higher profile design that requires cutting an opening in the rear bumber shroud. Obviously, there is a benefit to this design, as it looks as if it sits below the shroud ie, no shroud modification. Can anyone tell me what the hitch hight from the ground will be. I am concerned whether it will be a problem bottoming out off road or if a trailer tongue will ride pointing down too much.
asked by: Derek
Expert Reply:
I spoke with my contact at Curt Mfg. and was informed that there are definitely no clearance issues related with the hitch and that the hitch, once installed will sit just under the rear fascia on the 2011 Jeep Grand Cherokee. They did not have the height measurement for the hitch but provided the following information.
The receiver will be positioned level at the back of the vehicle and will not point down at all. If your trailer tongue is higher than the hitch when the trailer frame is level, you would need to use a drawbar with a rise to accommodate the height difference. We have an article detailing how to measure to select the correct ball mount for you to review, see link.
I have attached a picture that Curt Mfg was kind enough to send, showing the hitch installed on a 2011 Grand Cherokee for your reference.
Some items you may want to consider to complete your Class III towing setup are listed below.
Wiring # 118425
Drawbar # D-4
Hitch Ball # 19260 or # 19247
Hitch Lock # e98880
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitches - Flush - 2-5/8" Span - Chrome
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Chrome
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 7500 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Trailer Wiring Diagrams
- Q&A: Parts Needed to Install Brake Controller on 2012 Chrysler Town and Country
- Article: Brake Controller Installation: Starting from Scratch
- Article: Trailer Tester Battery Replacement for Part Number 8010
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Replacement for Demco Master Cylinder 05680-C for Drum Brakes
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: 2022 Toyota Highlander Wiring for a 7-Way Blade Connector
- Q&A: Troubleshooting Brake Override and Stop/Start Malfunction On 2022 Toyota Highlander Redarc Tow Pro
- Q&A: Replacement Hub for 2013 Wildwood 26TBSS Hub Drum with AL-KO 8700
- Q&A: Wiring Directions For Bargman LED Recessed Double Tail Light
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Q&A: Equal-I-Zer Weight Distribution is Too Stiff; Can Lighter Bars be Used in the Same Head
- Article: How to Charge RV Batteries