Propane Hose Replacements for Regulator

Question

Question:

I can't remove the regulator from the hose so I need the hose you just sent me and then also a 30 psi high pressure regulator with two female ends of you can help me with that please!

asked by: Adam D

0

Expert Reply:

We do have hoses which may work for you. The MB Sturgis Propane Pigtail # 100833-24 is a type 1 cylinder connection with a 1/4" male inverted flare. This is a 2 foot hose, though we also have a 15" hose # 100833-15 and 1 foot hose # 100575-12-MBS.

These hoses are also available with back check, the 20" # 100473-20-MBS, 15" # 100473-15-MBS and 12" # 100473-12.

I've added links to review videos of each of these products for you to take a look at.

expert reply by: Kyle S

0

click to enlarge

Adam

9/27/2017

I can't remove the regulator from the hose so I need the hose you just sent me and then also a 30 psi high pressure regulator with two female ends of you can help me with that please!

Reply

Kyle S.

9/27/2017

We may have what you are looking for, the MB Sturgis Single Stage Propane Regulator # 108072, which is a 30 psi regulator.

Reply

Answer 1

If you can send me a picture of the pigtail you're trying to replace or the inlet on your regulator I can confirm this, but it sounds like you need a pigtail with an NPT fitting as opposed to the Male Inverted Flare. The NPT pigtail which matches…

view full answer...

Answer 2

Yes. The pigtail could be the issue. I recommend replacing the pigtail with the MB Sturgis Propane Hose w/ Back Check - Type 1 x 1/4" MPT - 20" #100473-20-MBS. There is an internal back-check on Type 1 fittings that could be the issue.

view full answer...

Answer 3

Assuming that the 1 pound bottle can be removed and that the regulator on the grille can be used with a 20 pound tank then for a 12 inch supply hose you would need #CAM59053. It has a type 1 ACME nut at one end that connects to an ACME or P.O.L.…

view full answer...

Answer 4

The Automatic Changeover RV LP Gas Regulator #37207-30395 will work in place of the winntec model 6020 with no issues at all. With pigtails I suggest the MB Sturgis Propane Hose w/ Back Check - Type 1 x 1/4" MPT - 20" #100473-20-MBS.

view full answer...

Answer 5

A direct replacement for your Winntec Model 6020 is the Automatic Changeover RV LP Gas Regulator #37207-30395 as the BTU rating is compatible and they have the same fitting sizes.

view full answer...

Answer 6

I looked up the hose and the regulator you currently have, and found that the GHA7 hose uses an ACME Nut connector to the LP tank and a 1/4 inch male inverted flare that connects to the 3/8 to 1/4 adapter used on the regulator. We offer the necessary…

view full answer...

Answer 7

The fan in the #PD4645V is temperature controlled so typically it does not run continuously. However, if there are heavy loads you can expect the fan to run non-stop. According to Progressive Dynamics, this can also happen if you're charging…

view full answer...

Answer 8

100lb propane tanks typically have a female POL fitting so you'll just need to swap over the hoses to ones that have a male POL fitting and can still connect to your regulator/piping the same way the current hoses do. Most regulators have a 1/4…

view full answer...

Answer 9

Hello Gaby. I reached out to the manufacturer and found out that the UltraFab Weld-On Jumbo Steel Roller #UF48-979023 uses a 6-1.0mm Zerk fitting. For a replacement you can use the following: - Replacement Brass Grease Zerk for Weld-On Hinges - 6 mm…

view full answer...