Bearing Outside to Bearing Outside Measurement on Trailer Hub Assembly for 2K Axles T4084600042

Question

Question:

For part # T4084600042 what is the distance from inner bearing surface to outer bearing surface? Curious if it will fit my trailer spindle. All the diameters already check out.

asked by: Mike

0

Expert Reply:

Since the races (that go around the bearings) are already pressed in on Trailer Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Cast Item # T4084600042 I can measure from the outside of one to the outside of the other. That measurement is a hair less than 3-3/4 inches.

expert reply by: Michael H

0

Answer 1

In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your…

view full answer...

Answer 2

Lug nut torque is determined by a few factors. The size of the wheel, the metal the wheel is made from, the diameter of the studs etc. If you check out the chart I attached you'll see how to determine how much torque to use when installing a…

view full answer...

Answer 3

The trailer hub assembly, part number, 34822545BX, comes with the race attached to the hub. The seal and bearings are not attached. Those parts must be assembled and packed with grease prior to installing the cap. I have attached a FAQ sheet for…

view full answer...

Answer 4

The bearing number alone is not the best indicator for a specific grease or oil seal. Trailers with the same bearing number could have different seals based on the spindle or hub that is being used. Bearing number 30205 is not a bearing that we offer…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

I went out to the warehouse and found that the CE Smith Trailer Hub Assembly #CE13100 measured about 4-1/4" but that was with the plastic still wrapped around it. If you took the plastic away it would probably measure closed to 4-1/8". The…

view full answer...

Answer 7

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Bearing Outside to Bearing Outside Measurement on Trailer Hub Assembly for 2K Axles T4084600042

Featured Help Information

Miscellaneous Media

Continue Researching