Does the Draw-Tite Hitch # 75710 Hang Below the Bumper on the 2011 Ford Explorer
Question:
I am trying to find a base 2011 exployer but non of them have the trailer package . On the 2011 exployer does this hitch hang down below the bumper or will it fir just like a factory unit behind the removable plate on the rear bumper ? Thanks
asked by: Dennis S
Expert Reply:
The Draw-Tite trailer hitch # 76034 will hang below the bumper. It will not fit behind the removable plate on the rear bumper like the factory hitches do for your 2011 Ford Explorer.
If you plan on doing some towing you may also be interested in the following products to complete your setup:
Ball Mount 3/4 inch Rise or 2 inch Drop, part # D-4
Pin and Clip, part # PC3
Hitch Ball with 2 inch Diameter and Medium Shank, part # 19247
Hitch Ball with 1-7/8 inch Diameter and Medium Shank, part # 19260
Products Referenced in This Question
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Standard Color Code for Wiring Simple 4 Wire Trailer Lighting
- Article: Best Vehicles to Flat Tow Behind an RV
- Q&A: Where is Brake Controller Install Port for 2018 Ford Explorer
- Q&A: Wiring Diagram for Air Lift WirelessAIR Compressor System # AL74000
- Q&A: Can a 2020 Ram 2500 with Rambox Tow Fifth Wheel Trailer
- Q&A: Where Does Wiring Harness Plug Into on 2018 Ford Explorer
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Replacement Clearance Lights and SAE Codes On Light Lenses
- Q&A: Size of Factory Bolts For Installation of Curt Trailer Hitch Receiver in Factory Weldnuts
- Article: Troubleshooting 4 and 5-Way Wiring Installations
- Article: How to Measure for Trailer Hitch Drop
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: Trailer Hitch Balls