How Long are the Bars on the Top of Valterra Folding Manual Stabilizer for Trailers and RVs 020106

Question

Question:

How long are they ? on top

asked by: Phillip L

0

Expert Reply:

I went out to the warehouse to measure the upper part of the Valterra Folding Manual Stabilizer for Trailers and RVs - 14" to 28" Tall - Aluminum Item # 020106. The bars are 32-1/8 inches long. They are also 1 inch tall and 1 inch wide.

expert reply by: Michael H

0

click to enlarge

Answer 1

The Valterra Folding Manual Stabilizer for Trailers and RVs #020106 actually doesn't have a specific requirement for different lengths of trailers. It is really up to the end-user and how many they would like to install/can fit on their…

view full answer...

Answer 2

There is nothing that says you can't use Valterra Folding Manual Stabilizer #020106 for support for the back ramp door on your toy hauler. You would need at least 14 inches of clearance between the ground and the bottom of the ramp door when…

view full answer...

Answer 3

The Traffic Cone Holder, #RA-26, that you mentioned is designed to store cones that are 12" - 36" tall, and the arm of the holder is 22-3/8" long. The arm does not fold down a full 90 degrees, so this would not be the best option for…

view full answer...

Answer 4

I believe you are referring to slide-out supports, and it's pretty simple to choose the right one. All you need to do is measure from the ground to the bottom of the slide out track to get the correct height; the photo below shows where you want…

view full answer...

Answer 5

There many possible ways to mount a stabilizer jack such as the #TJ01RT-HD you looked at. Mounting them in the orientation shown the diagram would tend to work a bit better to stabilize the trailer against side to side movement, while having the…

view full answer...

Answer 6

When using the Valterra Folding Manual Stabilizer for Trailers #020106 you are not required to use a piece of wood for anything. Check out the picture I attached that shows the kit installed.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

How Long are the Bars on the Top of Valterra Folding Manual Stabilizer for Trailers and RVs 020106

Product Page this Question was Asked From

Continue Researching