Will Draw-Tite Trailer Hitch 36540 Fit a 2012 Toyota Camry with Dual Exhaust
Question:
Hello there, Will this hitch work with a 12 Camry with adual exhaust? And if not can you please recommend the appropriate hitch? Thanks a lot!
asked by: Frank D
Expert Reply:
Yes, Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" Item # 36540 will fit your 2012 Toyota Camry with dual exhaust. You will just follow any instructions pertaining to exhaust for both sides of the vehicle. The hitch was designed so that it could work with either exhaust configuration.
If you plan on doing some towing the recommended ball mount is # 36071. For a compatible 1-7/8 inch ball use # 19256 and for a compatible 2 inch ball use # 19258.
And for a trailer wiring harness use # 118405 to add a 4-Way flat trailer connector to the rear of the vehicle. I have included links to videos showing example installations of the trailer hitch and wiring for you.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Drawbar for 1-1/4" Hitch - 2-5/8" Rise, 3-1/4" Drop - 7-3/16" Long - 3.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 300 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Trailer Wiring Harness Recommendation for a 1999 Isuzu NPR
- Q&A: Brake Controller Installation on 2016 Mercedes-Benz Sprinter
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Battery Life and Charging Time For The Linxup GPS AT3 Tracking Device
- Q&A: Trailer GPS Device for Trailer Installation
- Q&A: How Much is Monthly Service for Linxup GPS Tracking Device
- Article: How to Install E-Track in 3 Easy Steps
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Q&A: Installation of Slipper Spring with Open Eye End
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Replacement Connector for a Pollak PA66-MD40
- Article: Best Vehicles to Flat Tow Behind an RV
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
- Article: Best Bike Racks for Electric Bikes