Parts Needed to Flat Tow 2005 Chrysler PT Cruiser
Question:
does this tow bar on pt do good with dinghy behind rv for pulling pt across country
asked by: Jim P
Expert Reply:
The base plate kit part # 278-1 is a confirmed fit for your 2005 Chrysler PT Cruiser and would work well in a flat towing setup to move your vehicle across the country.
In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle. The most popular compatible tow bar is the Falcon 2, # RM-520. For safety cables you can use # RM-643. The coiled design helps keep the cables off of the ground.
For lighting you can use the diode kit, # RM-15267, and not have to worry about cutting into the taillight housing. This will splice into your taillight wiring to allow your tow vehicle to control the taillight assemblies of the towed vehicle. This comes with a round 6-way connector that you will install on the front of your towed vehicle and enough coiled wire to go from there to the RV.
And finally, most states now require supplemental braking in the vehicle being flat towed. The easiest system to set up and use is the Blue Ox Patriot # BLU37TR, that applies the vehicle brakes in proportion to how much the tow vehicle is braking. This is the safest way to stop and it reduces wear and tear on both vehicles.
Most likely you will also need a high low adapter so that the tow bar will be level when you are flat towing. I attached a link to a page that has all of the ones we carry.
I have included a couple of helpful links to our articles on flat towing for you. Be sure to consult the vehicle owners manual for more specific information on flat towing your vehicle.
Products Referenced in This Question
Blue Ox Patriot Portable Flat Tow Brake System - Proportional
- Tow Bar Braking Systems
- Brake Systems
- Proportional System
- Recurring Set-Up
- Portable System
- Power Assist Brake Compatible
- Air Brakes
- Air Over Hydraulic Brakes
- Hydraulic Brakes
- Blue Ox
more information >
Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Tow Bar Wiring
- Splices into Vehicle Wiring
- Diode Kit
- Universal
- Tail Light Mount
- Roadmaster
more information >
Roadmaster Falcon 2 Tow Bar - RV Mount - 2" Hitch - 6,000 lbs
- Tow Bar
- Hitch Mount Style
- Telescoping
- Steel
- 6000 lbs
- Fits Roadmaster Base Plates - Crossbar
- Fits Roadmaster Base Plates - Direct Connect
- Stores on RV
- Standard
- Roadmaster
more information >
RoadMaster 68" Single Hook, Coiled Safety Cables - 6,000 lbs
- Safety Cables
- Coiled Cables
- 68 Inch Long
- 6000 lbs GTW
- Snap Hooks
- Coated Cables
- Roadmaster
more information >
Product Page this Question was Asked From
Roadmaster Crossbar-Style Base Plate Kit - Removable Arms
- Base Plates
- Removable Drawbars
- Hitch Pin Attachment
- Roadmaster
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Will Roadmaster XL Base Plate Kit # 278-1 Fit a 2006 Chrysler PT Cruiser
- Q&A: Can LED and Incandescent Lights be Mixed, Used at the Same Time on a Trailer
- Article: How to Choose a Battery Charger
- Article: Can You Flat Tow a MINI Cooper?
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: Diode Installation Instructions for a Dinghy with Separate Tail Light Wiring
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
- Q&A: Needed Equipment to Flat Tow a 2001 PT Cruiser Behind Motor Home
- Article: What Is a Supplemental Braking System?
- Q&A: Recommended Blue Ox Base Plate For A 2006 Chrysler Crossfire
- Q&A: Recommendation For Flat Towing a 2005 PT Cruiser Behind An RV
- Q&A: Wiring Diagram for Air Lift WirelessAIR Compressor System # AL74000
- Article: Flat Towing Package for 2007 Honda CR-V
- Q&A: Parts Needed to Flat Tow a 2007 Honda CR-V Behind a Motorhome